参数资料
型号: A6RV-102RF
元件分类: 开关
英文描述: ROTARY CODED SWITCH-10POSITIONS, REAL CODE, LATCHED, 0.025A, 24VDC, THROUGH HOLE-RIGHT ANGLE
封装: ROHS COMPLIANT
文件页数: 4/6页
文件大小: 672K
代理商: A6RV-102RF
4
Rotary DIP Switch
A6R/A6RV
Precautions
■ Cautions
Circuit Design
Use the switch within the rated voltage and current ranges, or the
switch may have a shortened life expectancy, radiate heat, or burn
out. Use circuit constants that ensure operation within the rated
ranges. This particularly applies to the instantaneous voltages and
currents when switching.
The reliability and lifetime of the switch may vary with the type of load
and other conditions. It is recommended that the switch is used in
actual applications only after correct operation is confirmed under the
conditions in which it will be used.
Mounting
Usually, the switch is set to 0. Do not change this setting throughout
the mounting and soldering procedures.
Soldering
Observe the following conditions when soldering the switch.
Automatic Soldering Bath (Flow Soldering Bath)
Soldering temperature: 260
° C max.
Soldering time:
5 s max. for a 1.6-mm thick, single-side PCB
Confirm in advance that flux will not bubble up onto the side of the
PCB to which the switch is mounted. Depending on the type, the flux
may have an adverse effect on the switch if it enters the switch
interior.
Manual Soldering
Soldering temperature: 350
° C at the tip of the soldering iron.
Soldering time:
3 s max. for a 1.6-mm thick, single-side PCB
Before soldering the switch on a PCB, make sure that there is no
unnecessary space between the switch and PCB.
Before soldering the switch on a multilayer PCB, carry out a test to
confirm that soldering can be performed properly. The switch may be
deformed by the soldering heat on the pattern or land of the multi-
layer PCB.
Do not solder the switch more than twice including rectification sol-
dering. An interval of five minutes is required between the first and
second soldering.
Washing
The switch cannot be washed.
Wipe dirt off the switch surface using alcohol.
Handling
Do not apply excessive operating force to the switch, or the switch
may be damaged or deformed, thus causing the switch mechanism
to malfunction as a result. Apply an operating force not exceeding
200% of the maximum rated operating force to the switch.
Set the switch with a flat-blade screwdriver that fits into the screw-
driver groove. Using a flat-blade screwdriver of inappropriate dimen-
sions, or using a tool other than a flat-blade screwdriver may cause
damage to the groove, and it may become impossible to operate the
switch.
相关PDF资料
PDF描述
A20415RNZQE ROTARY SWITCH-4POSITIONS, DP4T, LATCHED, 0.35A, 125VDC, PANEL MOUNT-THREADED
A20415RSCQ ROTARY SWITCH-4POSITIONS, DP4T, LATCHED, 0.35A, 125VDC, THROUGH HOLE-STRAIGHT
A20414MNZBF ROTARY SWITCH-4POSITIONS, DP4T, LATCHED, 0.02A, 20VDC, PANEL MOUNT-THREADED
A20414MSMCBE ROTARY SWITCH-4POSITIONS, DP4T, LATCHED, 0.02A, 20VDC, THROUGH HOLE-STRAIGHT
A20414RSMCQ ROTARY SWITCH-4POSITIONS, DP4T, LATCHED, 0.35A, 125VDC, THROUGH HOLE-STRAIGHT
相关代理商/技术参数
参数描述
A6RV102RS 制造商:Omron Electronic Components LLC 功能描述:SWIT DIP 10P 10 EXTD SHAFT 0.025A 24VDC PC PINS 2.54MM TH - Bulk 制造商:Omron Electronic Components LLC 功能描述:SWITCH ROTARY 10 POS 3X3 S 制造商:Omron Electronic Components LLC 功能描述:SWITCH, ROTARY, 10 POS, 3X3, SIDE
A6RV-102RS 功能描述:DIP 开关/ SIP 开关 BCD 3X3 SIDE EXT ACT RoHS:否 制造商:Omron Electronics 位置数量:10 开关类型:DIP 执行器:Rotary 端子节距:2.54 mm 触点形式: 端接类型:Solder Pin 电流额定值:100 mA 电压额定值 DC: 工作温度范围: 安装:Through Hole
A6RV161RF 制造商:Omron Electronic Components LLC 功能描述:SWIT DIP 16P 16 SCRWDRVR 0.025A 24VDC PC PINS 2.54MM TH - Rail/Tube
A6RV-161RF 功能描述:DIP 开关/ SIP 开关 HEX 4X1 SIDE ACT FLT RoHS:否 制造商:Omron Electronics 位置数量:10 开关类型:DIP 执行器:Rotary 端子节距:2.54 mm 触点形式: 端接类型:Solder Pin 电流额定值:100 mA 电压额定值 DC: 工作温度范围: 安装:Through Hole
A6RV161RS 制造商:Omron Electronic Components LLC 功能描述:SWIT DIP 16P 16 EXTD SHAFT 0.025A 24VDC PC PINS 2.54MM TH - Rail/Tube 制造商:Omron Electronic Components LLC 功能描述:SWITCH ROTARY 16 POS 4X1 S 制造商:Omron Electronic Components LLC 功能描述:SWITCH, ROTARY, 16 POS, 4X1, SIDE