- 您现在的位置：买卖IC网 > PDF目录1774 > A8438EEJTR-T (Allegro Microsystems Inc)IC PHOTOFLASH CHARGER 10-MLP PDF资料下载
参数资料
| 型号： | A8438EEJTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 13/15页 |
| 文件大小： | 0K |
| 描述： | IC PHOTOFLASH CHARGER 10-MLP |
| 标准包装： | 1 |
| 应用： | 照相机闪光灯电容器充电器 |
| 电流 - 电源： | 5mA |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-TDFN/MLP（3x3） |
| 包装： | 标准包装 |
| 产品目录页面： | 1141 (CN2011-ZH PDF) |
| 其它名称： | 620-1099-6 |
A8438
Photoflash Capacitor Charger with IGBT Driver
Applications Information
V OUT + V D_Drop
300 × 10 ? 9 × V OUT
L Primary ≥
Transformer Design
Turns Ratio. The minimum transformer turns ratio, N,
(Secondary:Primary) should be chosen based on the following
formula:
N ≥ (2)
40 ? V BATT
where:
V OUT (V) is the required output voltage level,
V D_Drop (V) is the forward voltage drop of the output diode(s),
V BATT (V) is the transformer battery supply, and
40 (V) is the rated voltage for the internal MOSFET switch,
representing the maximum allowable reflected voltage from the
output to the SW pin.
For example, if V BATT is 3.5 V and V D_Drop is 1.7 V (which could
be the case when two high voltage diodes were in series), and the
desired V OUT is 320 V, then the turns ratio should be at least 8.9.
In a worst case, when V BATT is highest and V D_Drop and V OUT are
at their maximum tolerance limit, N will be higher. Taking V BATT
= 5.5 V, V D_Drop = 2 V, and V OUT = 320 V × 102 % = 326.4 V as
the worst case condition, N can be determined to be 9.5.
In practice, always choose a turns ratio that is higher than the
calculated value to give some safety margin. In the worst case
example, a minimum turns ratio of N = 10 is recommended.
Primary Inductance . The A8438 has a minimum switch off-time,
t OFF(min) , of 300 ns, to ensure correct SW node voltage sensing.
As a loose guideline when choosing the primary inductance,
L Primary ( μ H), use the following formula:
. (3)
N × I SWLIM
Ideally, the charging time is not affected by transformer pri-
mary inductance. In practice, however, it is recommended that a
primary inductance be chosen between 6 μ H and 20 μ H. When
L Primary is much lower than 6 μ H, the converter operates at higher
frequency, which increases switching loss proportionally. This
leads to lower efficiency and longer charging time. When L Primary
is greater than 20 μ H, the rating of the transformer must be dra-
matically increased to handle the required power density, and the
series resistances are usually higher. A design that is optimized
to achieve a small footprint solution would have an L Primary of
7 to 14 μ H, with minimized leakage inductance and secondary
capacitance, and minimized primary and secondary series resist-
ance. Please refer to the table Recommended Components for
more information.
Leakage Inductance and Secondary Capacitance. The trans-
former design should minimize the leakage inductance to ensure
the turn-off voltage spike at the SW node does not exceed the
40 V limit. An achievable minimum leakage inductance for this
application, however, is usually compromised by an increase in
parasitic capacitance. Furthermore, the transformer secondary
capacitance should be minimized. Any secondary capacitance is
multiplied by N 2 when reflected to the primary, leading to high
initial current swings when the switch turns on, and to reduced
efficiency.
V BATT 1.5 to 5.5 V
T1
V BIAS 3.0to5.5V
Two Alkaline/NiMH/NiCAD or one Li +
D1
V OUT
Symbol
C1
Rating
0.1 μ F, X5R or X7R, 10 V
R5
100 k
R4
10 k
VIN
ILIM
C1
0.1 μ F
SW
FB
C2
4.7 μ F
R1
150 k
R2
150 k
COUT
100 μ F
330 V
C2
D1
T1
4.7 μ F, X5R or X7R, 10 V
Fairchild Semiconductor BAV23S
(dual diode connected in series)
TDK LDT565630T-041,
L Primary = 4.7 μ H, N = 10.2
DONE
A8438
R3
1.2 k
R1, R2
1206 resistors, 1 %
R6
10 k
R7
10 k
CHARGE
TRIGGER
GND
IGBTDRV
To IGBT Gate
R3
R4, R5
R6, R7
0603 resistor, 1 %
Pull-up resistors
Pull-down resistors
Figure 4. Typical circuit for photoflash application. Configured for I SWLIM of 2.0 A.
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
13
相关PDF资料 |
PDF描述 |
|---|---|
| A8439EEJTR-T | IC CHARGER PHOTO FLASH 10-MLP |
| A8447SLJTR-T | IC REG BUCK ADJ 3A 8SOIC |
| A8483EEK-T | IC REG BOOST ADJ 0.35A 5MLP |
| A8498SLJ-T | IC REG BUCK ADJ 3A 8SOIC |
| A8499SLJ-T | IC REG BUCK ADJ 2A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A8439 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Photoflash Capacitor Charger with IGBT Driver and Refresh |
| A8439EEJTR-T | 功能描述:IC CHARGER PHOTO FLASH 10-MLP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| A843DSC | 制造商:Pentair Technical Products / Hoffman 功能描述:Enclosure, Junction Box, 8.00x4.00x2.75in, Flat Cover, NEMA 4, Mild Steel 制造商:Pentair Technical Products / Hoffman 功能描述:ENCLOSURE JUNCTION BOX STEEL GRAY 制造商:Pentair Technical Products / Hoffman 功能描述:ENCLOSURE, JUNCTION BOX, STEEL, GRAY 制造商:Hoffman Enclosures 功能描述:SCREW COVER DSC ENCLOSURE8 X 4 X 2.75 制造商:Pentair Technical Products / Hoffman 功能描述:ENCLOSURE, JUNCTION BOX, STEEL, GRAY, Enclosure Type:Junction Box, Enclosure Mat 制造商:Pentair Technical Products / Hoffman 功能描述:ENCLOSURE, JUNCTION BOX, STEEL, GRAY, Enclosure Type:Junction Box, Enclosure Material:Steel, Body Color:Grey, External Height - Imperial:8", External Height - Metric:203mm, External Width - Imperial:4", External Width - Metric:102mm , RoHS Compliant: Yes |
| A844 | 制造商:TE Connectivity 功能描述:- Bulk |
| A8447 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:High Voltage Step Down Regulator |
发布紧急采购，3分钟左右您将得到回复。