- 您现在的位置：买卖IC网 > PDF目录20833 > A8512ELPTR-T (Allegro Microsystems Inc)IC LED DVR WHT/RGB BKLGT 24TSSOP PDF资料下载
参数资料
| 型号： | A8512ELPTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 12/18页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR WHT/RGB BKLGT 24TSSOP |
| 标准包装： | 8,000 |
| 拓扑： | 高端，低端，PWM，升压（升压） |
| 输出数： | 6 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 300kHz ~ 1MHz |
| 电源电压： | 8 V ~ 24 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
A8512
LED Backlight Driver for LCD Monitors and Televisions
100% Current. When the PWM signal is low, the LED sinks
turn off.
Referring to figure 13, there is a ramp-up delay between when
the PWM signal is applied and when the current reaches the
90% level. To improve current dimming linearity for PWM pulse
widths less than 100 μ s, increase the applied PWM pulse-width
by 3 to 5 μ s to compensate for this delay.
Startup Sequence When EN is pulled high, the IC enters
soft start. The IC first tries to determine which LEDx pins are
being used, by raising the LEDx pin voltage with a small current.
After a duration of 512 switching cycles, the LEDx pin voltage
is checked. Any LEDx channel with a drain voltage smaller then
100 mV is removed from the control loop. This is the reason why
unused LEDx pins should be connected to GND,
After the first PWM positive trigger, the boost current is limited
to 30% of normal value and all active LEDx pins sink 1 / 12 of
the set current until output voltage reaches sufficient regulation
level. When the device comes out of soft start, boost current and
the LEDx pin currents are set to normal operating level. Within
a few cycles, the output capacitor charges to the voltage required
to supply full LEDx current. After output voltage, V OUT , reaches
the required level, LEDx current toggles between 0% and 100%
with each PWM command signal.
In case of a heavy overload on V OUT at startup, the device will
stay in soft start mode indefinitely, as the output voltage cannot
rise to the LED regulation level.
LED Short Detect Any LEDx pins that have a voltage exceed-
ing the Short Circuit Detect Voltage, V SC , cause the device to
shut down and this condition is latched. This faults occurs when
multiple LEDs short. In case only a few LEDs short, the IC will
continue to work as long as power dissipation in the IC is limited.
Overvoltage Protection The A8512 has an adjustable over-
voltage protection feature to protect the power components
(external MOSFET, output diode and capacitors) against output
overvoltage. The overvoltage level can be set, from 19.5 V to a
higher voltage, with an external resistor, R OVP . When the current
though the OVP pin exceeds 200 μ A, internal OVP comparator
goes high and the device shuts down. The OVP fault disables all
LEDx strings that are below regulation, thus preventing them
For single-IC operation, select R OVP such that its OVP setpoint is
approximately 10 V above the LED operating voltage at cold. For
example, given the pin regulation voltage, V LEDx of 1.4 V (typ.), if
LED V F = 3.4 V (max.) and there are 15 LEDs in series, then the
operating voltage is approximately:
V OUT = 3.4 V × 15 + 1.4 V = 52.4 V .
In this case, select OVP at about 60 V, which gives R OVP = 200 k Ω .
Open LED Protection During normal operation, if any enabled
LED string opens, voltage on the corresponding LEDx pin goes
to zero. The boost loop operates in open loop till the OVP level
is reached. The A8512 identifies the open LED string when over-
voltage is detected. Open strings are then removed from the regu-
lation loop. Afterwards, the boost controller operates in normal
manner, and the output voltage is regulated to drive the remaining
strings. If the open LED string is reconnected, it will sink current
up to the programmed current level.
Note: Open strings are removed from boost regulation, but not
disabled. This keeps the string in operation if LEDs open for only
a short length of time, or reach OVP level on a transient event.
The disconnected string can be restored to normal mode by reen-
abling the IC. It can also be restored to normal operation if the
fault is removed from the corresponding LEDx pin, but an OVP
event occurs on any other LEDx pin.
Overcurrent Protection The IC provides pulse-by-pulse
current limiting for the boost MOSFET. The current limit level,
I SC (A), can be set by selecting the external resistor, R SC ( Ω ):
R SC = 0.095 / I SC . (6)
If the boost output voltage is unable to reach the regulation target
even when the switch is operating at maximum current limit, the
boost control loop will force the compensating capacitor, C COMP ,
to rise in voltage until it reaches the overcurrent fault level
(3.4 V approximately). The overcurrent fault forces the device
into soft start.
Thermal Shutdown (TSD) The IC shuts down when junction
temperature exceeds 165°C. It will recover automatically when
the junction temperature falls below 125°C approximately.
VIN Undervoltage Lockout (UVLO) The device is shut
down when input voltage, V IN , falls below V UVLO . Any existing
latched fault is cleared.
from controlling the boost output voltage.
Calculate the value for R OVP ( Ω ) as follows:
R OVP = ( V OVP – 19.5) / 200 μ A ,
where V OVP is the required OVP level in V.
(5)
V IN Operating Range Considerations When V IN is above
V UVLO and below 10 V, the IC will operate correctly, but its gate
driver voltage may not reach the regulation target of 7 V. This
may cause excessive switching and conduction loss if the external
MOSFET is not fully enhanced.
12
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
相关PDF资料 |
PDF描述 |
|---|---|
| 3-1624112-8 | INDUCTOR 7.5NH 680MA 0402 |
| P51-75-S-G-M12-4.5V-000-000 | SENSOR 75PSI 1/8-27NPT .5-4.5V |
| TA45-ABDWF200C0-799-AZM01 | CIRCUIT BRKR THERMAL 20A 2POLE |
| REC8-243.3SRWZ/H2/A/M/SMD-R | CONV DC/DC 8W 24VIN 3.3VOUT |
| REC3-483.3DRW/H2/A/CTRL | CONV DC/DC 3W 36-72VIN +/-3.3V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A8513 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Wide Input Voltage Range, High Efficiency Fault Tolerant LED Driver |
| A8513KLPTR-1-T | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Wide Input Voltage Range, High Efficiency Fault Tolerant LED Driver |
| A8513KLPTR-2-T | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Wide Input Voltage Range, High Efficiency Fault Tolerant LED Driver |
| A8513KLPTR-3-T | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Wide Input Voltage Range, High Efficiency Fault Tolerant LED Driver |
| A8513KLPTR-T | 功能描述:IC LED DRVR AUTO BCKLGHT 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 特色产品:LM3445 TRIAC Dimmable LED Driver 标准包装:55 系列:PowerWise® 恒定电流:是 恒定电压:- 拓扑:PWM，降压（降压） 输出数:1 内部驱动器:无 类型 - 主要:- 类型 - 次要:高亮度 LED（HBLED） 频率:30kHz ~ 1MHz 电源电压:8 V ~ 12 V 输出电压:- 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOICN 包装:管件 工作温度:-40°C ~ 125°C 产品目录页面:1285 (CN2011-ZH PDF) 其它名称:LM3445M |
发布紧急采购，3分钟左右您将得到回复。