- 您现在的位置：买卖IC网 > PDF目录364590 > AB-148 AB-148 - Low Sampling Rate Operation For Burr-Brown SoundPlus Audio Data Converters And CODECs PDF资料下载
参数资料
| 型号： | AB-148 |
| 元件分类： | Codec |
| 英文描述： | AB-148 - Low Sampling Rate Operation For Burr-Brown SoundPlus Audio Data Converters And CODECs |
| 中文描述： | 抗体- 148 -低采样率运作的Burr - Brown SoundPlus音频数据转换器和编解码器 |
| 文件页数： | 2/2页 |
| 文件大小： | 50K |
| 代理商： | AB-148 |
2
Figure 2 shows a simplified schematic of the ADS7843 front
end while using the PENIRQ. The resistive touch-screen is
represented with the row and column of series resistors
between the X and Y inputs. The switch, S1, models a
dynamic short that moves across the X and Y resistive touch-
screen axes like the tip of a PDA pen. S1 also models where
the tip of the PDA pen initially shorts the two resistive layers
together. I/O1 and I/O2 are general purpose input/output
ports from the MPU. I/O2 must be able to sense a change in
potential when powered down.
Be sure to note that the ADC will not start in the power-down
mode when power is applied to the system. Instead, the
MPU must write zeros into PD0 and PD1—two bits of the
Control Byte register. After the ADS7843 enters the power-
down mode, the Y-MOSFET provides a path for current flow
when the touch-screen is depressed. The other three
MOSFETs for X+, X–, and Y+ are in a high impedance state
during the power-down mode. When the PDA pen depresses
the touch-screen, current flows through the 100k
resistor
and the interrupt diode. Once PENIRQ is pulled LOW, a
voltage typically not exceeding 0.65V is sensed at I/O2. At
that time, the MPU should wake up, pull I/O1 and I/O2
LOW, then write a byte to the ADS7843 Control Byte
register to initiate a conversion. The MPU must drive I/O1
and I/O2 LOW in order to reverse bias the PENIRQ diode.
Otherwise, if the diode is forward-biased during a conver-
sion, the additional current will cause the input data to be
inaccurate. To complete the control cycle, the MPU writes
the corresponding power-down bits to the ADS7843 Control
Byte after the PDA has no inputs for a minute or two,
depending on the time allotted prior to the power-down
operation.
100k
S
1
PENIRQ
X+
Y+
X–
Y–
I/O1
I/O2
ADS7843
V
CC
FIGURE 2. Simplified PENIRQ Architecture.
相关PDF资料 |
PDF描述 |
|---|---|
| AB-150 | AB-150 - CREATING A BIPOLAR INPUT RANGE FOR THE DDC112 |
| AB-151 | AB-151 - FOUR-WIRE RTD CURRENT-LOOP TRANSMITTER: Four-Wire Connections to an RTD Allow the RTD to be Remotely Located from Active Circuitry. Yet Maintain Accuracy |
| AB-152 | AB-152 - DC MOTOR SPEED CONTROLLER: Control a DC Motor without Tachometer Feedback |
| AB-161 | AB-161 - AN ERROR ANALYSIS OF THE ISO102 IN A SMALL SIGNAL MEASURING APPLICATION |
| AB-162 | AB-162 - DC-TO-DC CONVERTER NOISE REDUCTION |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AB14-8A | 制造商:Thomas & Betts 功能描述:TERMINAL FLAG DISCONNECT #8 CRIMP 22 制造商:Thomas & Betts 功能描述:TERMINAL, FLAG DISCONNECT, #8, CRIMP, 22 制造商:Thomas & Betts 功能描述:TERMINAL, FLAG DISCONNECT, #8, CRIMP, 22-14AWG; Connector Type:Flag Disconnect; Series:Sta-Kon; Termination Method:Crimp; Stud/Tab Size:#8; Wire Size AWG Min:22AWG; Wire Size AWG Max:14AWG; Contact Material:Copper ;RoHS Compliant: Yes 制造商:Thomas & Betts 功能描述:TERMINAL, FLAG DISCONNECT, #8, CRIMP, 22-14AWG; Connector Type:Flag Disconnect; Series:Sta-Kon; Insulator Color:(Not Available); Termination Method:Crimp; Stud/Tab Size:#8; Wire Size AWG Min:22AWG; Wire Size AWG Max:14AWG ;RoHS Compliant: Yes 制造商:Thomas & Betts 功能描述:Flag Terminal 14-22AWG 13.97mm 7.87mm |
| AB-14N-W | 制造商:HellermannTyton 功能描述: |
| AB15 | 制造商:CIF 功能描述:BOARD FR4 2 SIDES 16/10 35 150X200MM 制造商:CIF 功能描述:BOARD FR4 2 SIDES 16/10 35, 150X200MM |
| AB-15.360MAGE-T | 功能描述:晶体 15.360MHz 30ppm 12pF -40C to 85C RoHS:否 制造商:AVX 频率:26 MHz 容差: 频率稳定性:50 PPM 负载电容:8 pF 端接类型:SMD/SMT 封装 / 箱体:1210 (3225 metric) 工作温度范围:- 40 C to + 150 C 尺寸:2.5 mm W x 3.2 mm L x 0.85 mm H 封装:Reel |
| AB15/GR | 制造商: 功能描述: 制造商:undefined 功能描述: |
发布紧急采购，3分钟左右您将得到回复。