- 您现在的位置：买卖IC网 > Datasheet目录307 > AC162049-2 (Microchip Technology)MOD PROGR UNIV MPLAB ICD2 ICD3 Datasheet资料下载
参数资料
| 型号： | AC162049-2 |
| 厂商： | Microchip Technology |
| 文件页数： | 1/1页 |
| 文件大小： | 0K |
| 描述： | MOD PROGR UNIV MPLAB ICD2 ICD3 |
| 标准包装： | 1 |
| 模块/板类型： | DIP 插座模块 |
| 适用于相关产品： | MPLAB? REAL ICE，ICD 3，PIC套件 3 |
Universal Programming Module
AC162049 Instruction Sheet
_________________________________________________
The Universal Programming Module (UPM) is a handy, low-cost board that supports the
programming of devices using the MPLAB ? ICD 2 in-circuit debugger. The UPM can also be
used with the MPLAB PM3 to IC2 Adapter (AC164111) for in-circuit programming with the
MPLAB PM3. The ZIF (Zero Insertion Force) in the UPM supports the programming of devices
in the DIP package type up to 40 pins with these development tools.
*****NOTICE*****
dsPIC ? DSC DEVICES CANNOT BE PROGRAMMED USING A UPM SETUP.
Configuration of the Jumpers: Configuration of the Jumpers:
ICD input at J1 is mapped to J3. There are seven jumpers
U1
(flying leads located at J3) that must be connected to pins
marked 1 through 40 on the two 20-pin headers (J4 and J5).
These connect the program mode, power supply, ground, clock
ICD J1
J4
J5
and data lines needed for programming from the development
tool to the device in socket U1. Configuration for these lines is
specific to the device being programmed. Please consult the
Datasheet for the proper jumper configuration for the device
being used. Further, the Release Notes for the tool in use may
also offer other detailed information about programming the
J3
device. Release Notes can be found under the Help option in
the MPLAB IDE.
*****NOTICE*****
THE UPM DOES NOT HAVE A JUMPER FOR LOW-VOLTAGE PROGRAMMING.
The UPM does not have a separate power source. Power is supplied to the UPM by the
development tool in use. MPLAB ICD 2 uses a 9V DC power supply (AC162039). The MPLAB
PM3 uses a 3V/5V DC power supply (ACICE0401).
Loading/Programming a Device: The ZIF socket (U1) will support up to 40-pin DIP packaged
devices. Be sure power is removed prior to inserting the device into the ZIF socket. Also, the
handle for the ZIF socket should be in the down position. The device should drop in with zero
force. Insert the device so that the top is aligned with the top of the ZIF socket (i.e., pin 1 to pin
1). Once the device is inserted, raise the handle on the socket 90 degrees to the full locked
position.
*****NOTICE*****
ZIF SOCKET HANDLE MUST BE IN THE UP (LOCKED) POSITION PRIOR TO
PROGRAMMING THE DEVICE OR IT WILL NOT PROGRAM PROPERLY.
LED 1 - Led 1 will illuminate whenever programming activity occurs.
Removing a Programmed Device: After MPLAB IDE or the MPLAB PM3 in Stand-Alone
mode acknowledges that communication is complete, lower the arm (unlock) on the ZIF
socket. The device should lift out without any resistance.
Microchip Technology Inc., 2355 W. Chandler Blvd., Chandler, AZ 85224 (480) 792-7200
DS51280B
相关PDF资料 |
PDF描述 |
|---|---|
| AC162049 | MODULE SOCKET FOR ICD2 DIP |
| AC163020 | ADAPTER PROGRAMMER PIC10F2XX |
| AC164032 | ADAPTER PICSTART PLUS 8DFN/DIP |
| AC164306 | MODULE SKT FOR PM3 20TSSOP |
| AC164324 | MODULE SKT FOR MPLAB 8DFN/16QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AC162050 | 功能描述:插座和适配器 For PIC12F629/75 RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| AC162051 | 功能描述:插座和适配器 28/40 PDIP for ICD RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| AC162051 | 制造商:Microchip Technology Inc 功能描述:HEADER INTERFACE (28/40 PDIP) |
| AC162052 | 功能描述:插座和适配器 for PIC16F676/630 RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| AC162053 | 功能描述:插座和适配器 For PIC16F627/8/48A RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
发布紧急采购，3分钟左右您将得到回复。