- 您现在的位置：买卖IC网 > Datasheet目录202 > ACA5-20PC-1-AC1-RL-C (Murata Power Solutions Inc)AMMETER LED 85-264VAC 50A RED Datasheet资料下载
参数资料
| 型号： | ACA5-20PC-1-AC1-RL-C |
| 厂商： | Murata Power Solutions Inc |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | AMMETER LED 85-264VAC 50A RED |
| 产品目录绘图： | Digital Panel Meter |
| 标准包装： | 12 |
| 系列： | ACA5-20PC |
| 类型： | 安培表 |
| 测量范围： | 0 ~ 50.0A |
| 显示器样式： | 红色字符，黑色背景 |
| 显示器类型： | LED |
| 显示器正面尺寸： | 1.30" L x 0.80" W（33.0 x 20.3mm） |
| 显示器位数： | 3.5 |
| 显示器位数 - 高度： | 0.370"（9.40mm） |
| 背光： | 无 |
| 安装类型： | 面板安装 |
| 端子： | 端接块 |
| 电源电压： | 85 ~ 264VAC |
| 产品目录页面： | 2856 (CN2011-ZH PDF) |
| 其它名称： | 811-1103 |
ACA5-20PC Series
5 Amp Input LED-Display AC Ammeters
ACA5-20PC series ammeters are not internally fused. Terminal block
TB1 is to be used only for powering the ammeters’ internal circuitry;
it must not be used to supply power to external loads. The supply
wires feeding these ammeters must be fused with a 0.25A/250V time
delay/time lag fuse, in accordance with applicable regulatory codes.
Wire insulation must be stripped to within ±10% of the stated dimen-
sions, and wires should be inserted into TB1 such that their insulation
is not pinched by the screw terminal.
ing one of the external 5A CT’s output leads to earth/chassis ground.
In the USA, consult the latest revision of the National Electrical Code
(NEC) for more information regarding CT grounding.
After all mechanical assembly is completed, connect the two output
leads of the external 5A CT to each other after they are run through
L1’s center hole. Pressure-style connectors (commonly refered to
as “wire nuts”) are acceptable as long as they are rated for the
number of conductors and voltage invloved.
4.
5.
6.
7.
8.
9.
AC Supply Polarity and Grounding: The two supply inputs, TB1-A
and TB1-B, on all ac-powered ACA5-20PC ammeters are not in
themselves polarity sensitive, that is, they have no internal "AC LO"
or "AC HI" designations. Also, ac-powered ACA5-20PC ammeters do
not include or require a connection to earth/chassis ground.
Connector Torque Ratings : It is important to tighten TB1's, screw-
terminals to their rated torque speci?cation of 3.6 pound-inches
(0.4Nm). Proper tightening will minimize connector losses and ensure
safe, reliable operation.
DC-Powered Models : DC-powered models draw minimal supply cur-
rents (120mA max.) and in most applications can be fused according
to the supply wire’s maximum amperage rating. However, be sure to
check and comply with all applicable codes and regulations to ensure
proper installation and operation.
Isolation : The on-board CT (L1) provides a minimum 2000Vdc
isolation between the current-carrying conductor passing through its
primary circuit and the ammeter supply voltage connected to TB1.
This isolation rating only applies to applications in which the load
wiring (i.e., the wire passing through L1’s center hole) does not con-
nect directly or indirectly to TB1-A or TB1-B.
CT Precautions : In normal operation, a 5A current transformer’s
secondary circuit operates at a very low voltage due to its closed-
loop operation and its low burden resistance. However, a CT can still
generate potentially lethal voltages if its output current is suddenly
interrupted. For example, loose CT secondary connections can cause
a condition referred to as “inductive kick". Inductive kick can generate
extremely high voltages across intermitent secondary connections.
Therefore, implementing connections to any 5A current transformer’s
output leads must only be performed with zero load-current, that is,
with no power applied to the load circuit.
CT Connections and Grounding : Some applications require connect-
10. Replacing Analog Panel Meters: ACA5-20PC ammeters can be
used as direct replacements for analog panel meters driven by
5A?CT’s. All wiring operations must be performed with both the
load and the supply power sources completely de-energized.
PANEL INSTALLATION
All connections to ACA5-20PC Series ammeters must be made after the
ammeter is securely attached to the panel and with all load and supply
voltages de-energized (off).
Care should be exercised when passing conductors through the ammeter’s
built-in CT. The installed wire positions should be such that minimal
forces are applied to the built-in CT, TB1, or to the ammeter itself. In
high-vibration environments, proper strain reliefs must be used for all
load and supply wiring.
To ensure a secure panel-mount installation, MPS recommends using the
DMS-BZL4-C bezel assembly (with sealing gasket) supplied with each
ammeter. See Mechanical Speci?cations for detailed cutout and ammeter
dimensions.
Following the four-step sequence shown in Figure 2 — being careful not
to apply excessive force or twisting motions — insert the ammeter into
the panel opening. When using the DMS-BZL4-C, install its sealing gas-
ket so it is positioned between the ammeter’s front ?ange and panel front
surface (see Mechanical Speci?cations). Be sure to use and securely
tighten all four screws supplied with the bezel assembly.
Step 1.
Step 2.
Step 3.
Step 4.
P A N E L
P A N E L
P A N E L
B E Z E L
P A N E L
3
1
4
2
G A S K E T
( o p tio n a l)
Figure 2. Panel Installation
www.murata-ps.com/support
ACA5-20PC_B05 Page 3 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| ACA5-20RM-5-AC3-RL-C | AMMETER AC 200A 120VAC RED |
| ACB120DHNN | CONN EDGECARD 240PS .050 DIP SLD |
| ACB92DHHR-S378 | CONN EDGECARD 184PS PCI64 5V |
| ACC70DKSH-S1191 | CONN EDGECARD 140PS .100 DIP SLD |
| ACC70DRSN-S273 | CONN EDGECARD 140PS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ACA5-20PC-1-AC2-RL | 功能描述:数字面板表 0-50.0A input range 3 1/2 Digit Red LED RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM |
| ACA5-20PC-1-DC1-RL | 功能描述:数字面板表 0-50.0A input range 3 1/2 Digit Red LED RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM |
| ACA5-20PC-1-DC1-RL-C | 功能描述:数字面板表 0-50.0A input range 3 1/2 Digit Red LED RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM |
| ACA5-20PC-2-AC1-RL | 功能描述:数字面板表 0-75.0A input range 3 1/2 Digit Red LED RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM |
| ACA5-20PC-2-AC1-RL-C | 功能描述:数字面板表 0-1999AInput RedLEDDisplay5A RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM |
发布紧急采购，3分钟左右您将得到回复。