参数资料
| 型号： | ACCESS-TOUCH-SS |
| 厂商： | Flexipanel |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR TOUCH KEYED 20-SSOP |
| 标准包装： | 25 |
| 系列： | * |
| 其它名称： | 658-1046-5 |
p3 of 4
7-Sep-08
Access-Touch
HW140-1
www.firmwarefactory.com
sequences longer than the minimum code length cannot
be specified, e.g. 12341234.
Typically the set switch will only be accessible from
inside the secured-access area, or will be implemented
as a key switch.
The code set by default is 123.
Lock, Lock#
The lock outputs control the access lock. These pins
can drive up to 25mA, sufficient for a small relay.
Click1, Click2
Connect to a buzzer to provide audio feedback:
High note:
Button press registered
Medium note: Code set
Low note:
Lock open
These pins can drive up to 25mA, so a current limiting
series resistor may be required. This is the function of
R12 in figure 1, which also serves as a volume control.
Touch Pad Design
The touch pads need to be designed for maximum
capacitance when a finger is present, and minimum
capacitance when not present. The design shown in
figure 1 has been shown to be effective, with a track
width of 1.1mm and gap of 0.33mm. The overall pad
size should be at least 13mm square, with a minimum
gap between pads of 5mm.
No physical contact is required and the touch pads may
be overlaid with, for example, a label or thin acrylic
panel. Alternatively, the pad may be placed in an inner
PCB layer immediately below the exposed PCB surface.
Button presses are detected as a rise in capacitance in
one or two sense lines. Too high a trigger sensitivity
can be just as troublesome as low a trigger sensitivity.
Therefore the sensitivity setting may require adjustment
to suit a particular physical setup.
(See nonvolatile
settings section below.)
To avoid ambiguity, it is important that fingers do not
induce capacitance
where not wanted.
Avoid
unnecessary routing tracks on the exposed surface of
the PCB. Apart from the touch pads, the circuit should
avoid being placed where fingers might get close. Avoid
metal enclosures.
Non-Volatile Settings
Various settings can be specified in the code memory at
programming time (see the Programming AccessTouch
section). Alternatively, they may be set in EEPROM
memory at a later date using a PIC programmer. The
EEPROM locations are shown in table 4.
Table 4. Nonvolatile Settings In EEPROM
Address
Name
Default
Description
0x00
UseEE
0x00
Zero to use code memory
settings, or non-zero for
EEPROM settings
0x01
Sens
0x38
Touch trigger sensitivity
0x02
OpTime
0x08
Lock open time, 1/3s units
0x03
OpBeep
0x01
Zero for no beep on unlock
Table 4. Nonvolatile Settings In EEPROM
Address
Name
Default
Description
0x04
WaitSlp
0x00
Wait time before entering
sleep mode, or zero for no
sleep, 1/15s units
0x05
MinLen
0x03
Minimum number of digits
permitted in a new code.
Note that the access code is also stored in EEROM and
is visible to anybody with a PIC programmer.
Firmware Delivery on HexWax
If not bought as a pre-programmed chip,
AccessTouch
firmware
is
available
as
an
encrypted
firmware
download
from
www.hexwax.com. To download it you will need a
TEAclipper/PIC HV and a TEAclipper/USB adapter.
To load the firmware onto the TEAclipper, start the
HexWax Explorer firmware and log in.
Then
download the AccessTouch firmware pack from
the
hexwax.com
products
section.
When
download completes, an AccessTouch folder will
appear in the Local Files section of HexWax
Explorer. In this folder is the AccessTouch.wax
file that contains the firmware.
You will need AccessTouch license credits in order
to decrypt the AccessTouch.wax file.
Contact
hexwax.com for details of payment options and
how to obtain free samples.
Once you have license credits, select the
AccessTouch.wax file and insert a TEAclipper/PIC
HV into the TEAclipper/USB adapter. Press the
Charge Now… button. Referring to figure 3, select
how many licenses you wish to load onto the
TEAclipper. Additionally, select the desired Non-
Volatile Settings written into code memory as
MinLen-WaitSlp-OpBeep-OpTime-Sens (refer to
table 4). For example, for the default settings,
enter 0300010838. Finally press OK to obtain a
decryption key and to charge the TEAclipper with
the decrypted firmware.
Figure 3: Decrypting the AccessTouch.wax file
相关PDF资料 |
PDF描述 |
|---|---|
| AD1362KD | IC CONV 16CH 32-CDIP |
| 100-1215-1 | MODULE ECM-BF561-C-I-Q25S128F32 |
| 100-1221-3 | CORE MOD CM-BF537E 600MHZ CONN |
| 100-1225-1 | CORE MOD TCM-BF537 500MHZ CONN |
| 100-1254-2 | MODULE BF527-C-C-Q50S64F8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ACC-F01-1 | 制造商:E-Switch Inc 功能描述:SWITCH CAP BLACK |
| ACC-F01-2 | 制造商:E-Switch Inc 功能描述:SWITCH CAP CLEAR |
| ACC-F02-1 | 制造商:E-Switch Inc 功能描述:CAP - FOR ROCKER SWITCH |
| ACC-F03-1 | 制造商:E-Switch Inc 功能描述:CAP - FOR ROCKER SWITCH 制造商:E-Switch Inc 功能描述:ACC ESW |
| ACCF032 | 功能描述:SWITCH CAP RoHS:是 类别:开关 >> 配件 - 帽盖 系列:* 标准包装:1 系列:AP 开关类型:按钮 形状:圆形，凸起（圆顶） 颜色:红 发光:发光开口 适用于相关产品:AP 系列 安装类型:卡入式 尺寸:12.35mm 直径 x 6.25mm H 特点:- 配用:AP2N006TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N003TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N002TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N006SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N003SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N002SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP4N007SWBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N007TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N007SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP4N006TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125V更多... 其它名称:*481D03001 |
发布紧急采购，3分钟左右您将得到回复。