- 您现在的位置：买卖IC网 > PDF目录68990 > ACPM-5204-BLK 1710 MHz - 1755 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER PDF资料下载
参数资料
| 型号： | ACPM-5204-BLK |
| 元件分类： | 放大器 |
| 英文描述： | 1710 MHz - 1755 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| 封装： | 3 X 3 MM, GREEN PACKAGE-10 |
| 文件页数： | 4/13页 |
| 文件大小： | 314K |
| 代理商： | ACPM-5204-BLK |
12
Storage Condition
Packages described in this document must be stored
in sealed moisture barrier, antistatic bags. Shelf life in a
sealed moisture barrier bag is 12 months at <40°C and
90% relative humidity (RH) J-STD-033 p.7.
Out-of-Bag Time Duration
After unpacking the device must be soldered to the PCB
within 168 hours as listed in the J-STD-020B p.11 with
factory conditions <30°C and 60% RH.
Baking
It is not necessary to re-bake the part if both conditions
(storage conditions and out-of bag conditions) have been
satised. Baking must be done if at least one of the con-
ditions above have not been satised. The baking condi-
tions are 125°C for 12 hours J-STD-033 p.8.
CAUTION
Tape and reel materials typically cannot be baked at the
temperature described above. If out-of-bag exposure
time is exceeded, parts must be baked for a longer time
at low temperatures, or the parts must be de-reeled,
de-taped, re-baked and then put back on tape and reel.
(See moisture sensitive warning label on each shipping
bag for information of baking).
Board Rework
Component Removal, Rework and Remount
If a component is to be removed from the board, it is
recommended that localized heating be used and the
maximum body temperatures of any surface mount
component on the board not exceed 200°C. This method
will minimize moisture related component damage. If any
component temperature exceeds 200°C, the board must
be baked dry per 4-2 prior to rework and/or component
removal. Component temperatures shall be measured at
the top center of the package body. Any SMD packages
that have not exceeded their oor life can be exposed to
a maximum body temperature as high as their specied
maximum reow temperature.
Removal for Failure Analysis
Not following the above requirements may cause
moisture/reow damage that could hinder or com-
pletely prevent the determination of the original failure
mechanism.
Baking of Populated Boards
Some SMD packages and board materials are not able to
withstand long duration bakes at 125°C. Examples of this
are some FR-4 materials, which cannot withstand a 24 hr
bake at 125°C. Batteries and electrolytic capacitors are
also temperature sensitive. With component and board
temperature restrictions in mind, choose a bake tem-
perature from Table 4-1 in J-STD 033; then determine the
appropriate bake duration based on the component to
be removed. For additional considerations see IPC-7711
andIPC-7721.
Derating due to Factory Environmental Conditions
Factory oor life exposures for SMD packages removed
from the dry bags will be a function of the ambient envi-
ronmental conditions. A safe, yet conservative, handling
approach is to expose the SMD packages only up to the
maximum time limits for each moisture sensitivity level
as shown in next table. This approach, however, does not
work if the factory humidity or temperature is greater
than the testing conditions of 30°C/60% RH. A solution
for addressing this problem is to derate the exposure
times based on the knowledge of moisture diusion in
the component package materials ref. JESD22-A120).
Recommended equivalent total oor life exposures can
be estimated for a range of humidities and temperatures
based on the nominal plastic thickness for each device.
Table on next page lists equivalent derated oor lives for
humidities ranging from 20-90% RH for three tempera-
ture, 20°C, 25°C, and 30°C.
Table on next page is applicable to SMDs molded
with novolac, biphenyl or multifunctional epoxy mold
compounds. The following assumptions were used in cal-
culating this table:
1. Activation Energy for diusion = 0.35eV (smallest
known value).
2. For ≤60% RH, use Diusivity = 0.121exp ( -0.35eV/kT)
mm2/s (this used smallest known Diusivity @ 30°C).
3. For >60% RH, use Diusivity = 1.320exp ( -0.35eV/kT)
mm2/s (this used largest known Diusivity @ 30°C).
相关PDF资料 |
PDF描述 |
|---|---|
| ACPM-5204-TR1 | 1710 MHz - 1755 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| ACPM-7311-BLK | 824 MHz - 849 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| ACPM-7311-TR1 | 824 MHz - 849 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| ACPM-7371-TR1 | 880 MHz - 915 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| ACPM-7813-BLK | 824 MHz - 849 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ACPM-5204-TR1 | 制造商:AVAGO 制造商全称:AVAGO TECHNOLOGIES LIMITED 功能描述:UMTS Band4 (1710-1755MHz) 3x3mm Power Amplifi er Module |
| ACPM-5205 | 制造商:AVAGO 制造商全称:AVAGO TECHNOLOGIES LIMITED 功能描述:UMTS Band5 (824-849MHz) 3x3mm Power Amplifier Module |
| ACPM-5205-BLK | 制造商:AVAGO 制造商全称:AVAGO TECHNOLOGIES LIMITED 功能描述:UMTS Band5 (824-849MHz) 3x3mm Power Amplifier Module |
| ACPM-5205-TR1 | 制造商:AVAGO 制造商全称:AVAGO TECHNOLOGIES LIMITED 功能描述:UMTS Band5 (824-849MHz) 3x3mm Power Amplifier Module |
| ACPM-5208 | 制造商:AVAGO 制造商全称:AVAGO TECHNOLOGIES LIMITED 功能描述:UMTS Band8 (880-915MHz) 3x3mm Power Amplifi er Module |
发布紧急采购，3分钟左右您将得到回复。