- 您现在的位置：买卖IC网 > PDF目录97841 > ACPM-7311-BLKR 824 MHz - 849 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER PDF资料下载
参数资料
| 型号： | ACPM-7311-BLKR |
| 元件分类： | 放大器 |
| 英文描述： | 824 MHz - 849 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| 封装： | 4 X 4 MM, 1.10 MM HEIGHT, ROHS COMPLIANT, PLASTIC, 10 PIN |
| 文件页数： | 6/16页 |
| 文件大小： | 728K |
| 代理商： | ACPM-7311-BLKR |
4
Storage Condition
Packages described in this document must be stored
in sealed moisture barrier, antistatic bags. Shelf life in a
sealed moisture barrier bag is 12 months at <40°C and
90% relative humidity (RH) J-STD-033 p.7.
Out-of-Bag Time Duration
After unpacking the device must be soldered to the PCB
within 168 hours as listed in the J-STD-020B p.11 with
factory conditions <30°C and 60% RH.
Baking
It is not necessary to re-bake the part if both conditions
(storage conditions and out-of bag conditions) have been
satisfied. Baking must be done if at least one of the con-
ditions above have not been satisfied. The baking condi-
tions are 125°C for 12 hours J-STD-033 p.8.
CAUTION
Tape and reel materials typically cannot be baked at the
temperature described above. If out-of-bag exposure
time is exceeded, parts must be baked for a longer time
at low temperatures, or the parts must be de-reeled, de-
taped, re-baked and then put back on tape and reel. (See
moisture sensitive warning label on each shipping bag for
information of baking).
Board Rework
Component Removal, Rework and Remount
If a component is to be removed from the board, it is
recommended that localized heating be used and the
maximum body temperatures of any surface mount
component on the board not exceed 200°C. This method
will minimize moisture related component damage. If any
component temperature exceeds 200°C, the board must
be baked dry per 4-2 prior to rework and/or component
removal. Component temperatures shall be measured at
the top center of the package body. Any SMD packages
that have not exceeded their floor life can be exposed to
a maximum body temperature as high as their specified
maximum reflow temperature.
Removal for Failure Analysis
Not following the above requirements may cause
moisture/reflow damage that could hinder or com-
pletely prevent the determination of the original failure
mechanism.
Baking of Populated Boards
Some SMD packages and board materials are not able to
withstand long duration bakes at 125°C. Examples of this
are some FR-4 materials, which cannot withstand a 24 hr
bake at 125°C. Batteries and electrolytic capacitors are
also temperature sensitive. With component and board
temperature restrictions in mind, choose a bake tem-
perature from Table 4-1 in J-STD 033; then determine the
appropriate bake duration based on the component to
be removed. For additional considerations see IPC-7711
andIPC-7721.
Derating due to Factory Environmental Conditions
Factory floor life exposures for SMD packages removed
from the dry bags will be a function of the ambient en-
vironmental conditions. A safe, yet conservative, handling
approach is to expose the SMD packages only up to the
maximum time limits for each moisture sensitivity level as
shown in Table 7. This approach, however, does not work
if the factory humidity or temperature is greater than the
testing conditions of 30°C/60% RH. A solution for address-
ing this problem is to derate the exposure times based on
the knowledge of moisture diffusion in the component
package materials ref. JESD22-A120). Recommended
equivalent total floor life exposures can be estimated for
a range of humidities and temperatures based on the
nominal plastic thickness for each device.
Table 9 lists equivalent derated floor lives for humidities
ranging from 20-90% RH for three temperature, 20°C,
25°C, and 30°C.
This table is applicable to SMDs molded with novolac,
biphenyl or multifunctional epoxy mold compounds. The
following assumptions were used in calculating Table 9:
1. Activation Energy for diffusion = 0.35eV (smallest
known value).
2. For ≤60% RH, use Diffusivity = 0.121exp ( -0.35eV/kT)
mm2/s (this used smallest known Diffusivity @ 30°C).
3. For >60% RH, use Diffusivity = 1.320exp ( -0.35eV/kT)
mm2/s (this used largest known Diffusivity @ 30°C).
相关PDF资料 |
PDF描述 |
|---|---|
| ACPM-7311-OR1 | 824 MHz - 849 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| ACPM-7331-OR1 | 1850 MHz - 1910 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| ACPM-7331-TR1 | RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| ACPM-7381 | 1920 MHz - 1980 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| ACPM-7382-BLK | 1920 MHz - 1980 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ACPM-7311-OR1 | 功能描述:射频放大器 UMTS800 Power Amp Module RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| ACPM-7311-TR1 | 功能描述:射频放大器 UMTS800 Power Amp Module RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| ACPM-7312-BLK | 功能描述:射频放大器 UMTS PA Module Band 5 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| ACPM-7312-TR1 | 功能描述:射频放大器 UMTS PA Module Band 5 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| ACPM-7331-BLK | 功能描述:射频放大器 UMTS1900 Power Amp Module RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。