- 您现在的位置：买卖IC网 > PDF目录10670 > AD1877JRZ (Analog Devices Inc)IC ADC STEREO 16BIT 28-SOIC PDF资料下载
参数资料
| 型号： | AD1877JRZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 20/20页 |
| 文件大小： | 0K |
| 描述： | IC ADC STEREO 16BIT 28-SOIC |
| 标准包装： | 27 |
| 位数： | 16 |
| 采样率（每秒）： | 48k |
| 数据接口： | 串行 |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 315mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
| 输入数目和类型： | 2 个单端，单极 |
| 产品目录页面： | 777 (CN2011-ZH PDF) |
AD1877
REV. A
–9–
The ground planes should be tied together at one spot under-
neath the center of the package with an approximately 3 mm
trace. This ground plane technique also minimizes RF transmis-
sion and reception.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
L
RCK
WCLK
BCLK
DGND1
DVDD1
RDEDGE
S/
M
384/
256
AVDD
VINL
CAPL1
CAPL2
AGNDL
VREFL
CLKIN
TAG
SOUT
DVDD2
RESET
MSBDLY
R
LJUST
AGND
VINR
CAPR1
CAPR2
AGNDR
VREFR
DGND2
DIGITAL GROUND PLANE
ANALOG GROUND PLANE
Figure 4. Recommended Ground Plane
Each reference pin (14 and 15) should be bypassed with a 0.1
F
ceramic chip capacitor in parallel with a 4.7
F tantalum capaci-
tor. The 0.1
F chip cap should be placed as close to the pack-
age pin as possible, and the trace to it from the reference pin
should be as short and as wide as possible. Keep this trace away
from any analog traces (Pins 10, 11, 12, 17, 18, 19)! Coupling
between input and reference traces will cause even order har-
monic distortion. If the reference is needed somewhere else on
the printed circuit board, it should be shielded from any signal
dependent traces to prevent distortion.
Wherever possible, minimize the capacitive load on the digital
outputs of the part. This will reduce the digital spike currents
drawn from the digital supply pins and help keep the IC sub-
strate quiet.
How to Extend SNR
A cost-effective method of improving the dynamic range and
SNR of an analog-to-digital conversion system is to use multiple
AD1877 channels in parallel with a common analog input. This
technique makes use of the fact that the noise in independent
modulator channels is uncorrelated. Thus every doubling of the
number of AD1877 channels used will improve system dynamic
range by 3 dB. The digital outputs from the corresponding deci-
mator channels have to be arithmetically averaged to obtain the
improved results in the correct data format. A microprocessor,
either general-purpose or DSP, can easily perform the averaging
operation.
Shown below in Figure 5 is a circuit for obtaining a 3 dB
improvement in dynamic range by using both channels of a
single AD1877 with a mono input. A stereo implementation
would require using two AD1877s and using the recommended
input structure shown in Figure 2. Note that a single microproces-
sor would likely be able to handle the averaging requirements
for both left and right channels.
AD1877
RECOMMENDED
INPUT BUFFER
SINGLE
CHANNEL
INPUT
DIGITAL
AVERAGER
AD1877
VINR
VINL
SINGLE
CHANNEL
OUTPUT
Figure 5. Increasing Dynamic Range By Using Two
AD1877 Channels
DIGITAL INTERFACE
Modes of Operation
The AD1877’s flexible serial output port produces data in
two’s-complement, MSB-first format. The input and output sig-
nals are TTL logic level compatible. Time multiplexed serial
data is output on SOUT (Pin 26), left channel then right chan-
nel, as determined by the left/right clock signal LRCK (Pin 1).
Note that there is no method for forcing the right channel to
precede the left channel. The port is configured by pin selec-
tions. The AD1877 can operate in either master or slave mode,
with the data in right-justified, I
2S-compatible, Word Clock
controlled or left-justified positions.
The various mode options are pin-programmed with the Slave/
Master Pin (7), the Right/Left Justify Pin (21), and the MSB
Delay Pin (22). The function of these pins is summarized as
follows:
相关PDF资料 |
PDF描述 |
|---|---|
| VE-23N-IX-B1 | CONVERTER MOD DC/DC 18.5V 75W |
| VI-21D-IX-B1 | CONVERTER MOD DC/DC 85V 75W |
| AD9204BCPZ-40 | IC ADC 10BIT 40MSPS DL 64LFCSP |
| VI-21B-IX-B1 | CONVERTER MOD DC/DC 95V 75W |
| VE-23H-IX-B1 | CONVERTER MOD DC/DC 52V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD1877JRZ | 制造商:Analog Devices 功能描述:IC 16-BIT STEREO ADC |
| AD1877JRZ-RL | 功能描述:IC ADC STEREO 16BIT 28-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD1878 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Performance 16-/18-Bit Stereo ADCs |
| AD1878JD | 制造商:AD 制造商全称:Analog Devices 功能描述:High Performance 16-/18-Bit Stereo ADCs |
| AD1879 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Performance 16-/18-Bit Stereo ADCs |
发布紧急采购，3分钟左右您将得到回复。