参数资料
| 型号： | AD204KN |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC AMP ISOL 5KHZ QUAD LP 38DIP |
| 标准包装： | 1 |
| 放大器类型： | 隔离 |
| 电路数： | 4 |
| 增益带宽积： | 5kHz |
| 电流 - 输入偏压： | 30pA |
| 电压 - 输入偏移： | 5000µV |
| 电流 - 输出 / 通道： | 2mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 38-DIP（0.500"，12.70mm），11 引线 |
| 供应商设备封装： | 10-PDIP |
| 包装： | 管件 |
REV. D
AD202/AD204
–6–
Adjustments. When gain and zero adjustments are needed, the
circuit details will depend on whether adjustments are to be made
at the isolator input or output, and (for input adjustments) on
the input circuit used. Adjustments are usually best done on the
input side, because it is better to null the zero ahead of the gain,
and because gain adjustment is most easily done as part of the
gain-setting network. Input adjustments are also to be preferred
when the pots will be near the input end of the isolator (to mini-
mize common-mode strays). Adjustments on the output side
might be used if pots on the input side would represent a hazard
due to the presence of large common-mode voltages during
adjustment.
Figure 8a shows the input-side adjustment connections for use
with the noninverting connection of the input amplifier. The
zero adjustment circuit injects a small adjustment voltage in series
with the low side of the signal source. (This will not work if the
source has another current path to input common or if current
flows in the signal source LO lead). Since the adjustment volt-
age is injected ahead of the gain, the values shown will work for
any gain. Keep the resistance in series with input LO below a
few hundred ohms to avoid CMR degradation.
AD202
OR
AD204
47.5k
VS
5k
GAIN
RG
200
+7.5
–7.5
100k
ZERO
2k
50k
Figure 8a. Adjustments for Noninverting Connection of
Op Amp
Also shown in Figure 8a is the preferred means of adjusting the
gain-setting network. The circuit shown gives a nominal RF of
50 k
W, and will work properly for gains of ten or greater. The
adjustment becomes less effective at lower gains (its effect is
halved at G = 2) so that the pot will have to be a larger fraction
of the total RF at low gain. At G = 1 (follower) the gain cannot
be adjusted downward without compromising input resistance;
it is better to adjust gain at the signal source or after the output.
Figure 8b shows adjustments for use with inverting input cir-
cuits. The zero adjustment nulls the voltage at the summing
node. This method is preferable to current injection because it is
less affected by subsequent gain adjustment. Gain adjustment is
again done in the feedback; but in this case it will work all the
way down to unity gain (and below) without alteration.
AD202
OR
AD204
RS
47.5k
VS
5k
GAIN
200
50k
+7.5
–7.5
100k
ZERO
Figure 8b. Adjustments for Summing or Current Input
Figure 9 shows how zero adjustment is done at the output by
taking advantage of the semi-floating output port. The range of
this adjustment will have to be increased at higher gains; if that
is done, be sure to use a suitably stable supply voltage for the
pot circuit.
There is no easy way to adjust gain at the output side of the
isolator itself. If gain adjustment must be done on the output
side, it will have to be in a following circuit such as an output
buffer or filter.
AD202
OR
AD204
200
50k
100k
ZERO
0.1 F
+15V
–15V
VO
Figure 9. Output-Side Zero Adjustment
Common-Mode Performance. Figures 10a and 10b show
how the common-mode rejection of the AD202 and AD204
varies with frequency, gain, and source resistance. For these
isolators, the significant resistance will normally be that in the
path from the source of the common-mode signal to IN COM.
The AD202 and AD204 also perform well in applications re-
quiring rejection of fast common-mode steps, as described in
the Applications section.
FREQUENCY – Hz
180
10
CMR
–
dB
160
140
120
100
80
60
40
20
50 60 100
200
500
1k
2k
5k
G = 100
G = 1
R
LO
= 10k
R
LO = 500
R
LO = 0
R
LO = 0
R
LO
= 10k
Figure 10a. AD204
(NOTE: Circuit figures shown on this page are for SIP-style packages. Refer to
Page 3 for proper DIP package pinout.)
相关PDF资料 |
PDF描述 |
|---|---|
| TSM-105-01-L-DV-LC | CONN HEADER 10POS .100" DBL SMD |
| 552699-2 | CONN TERMINAL 28-18AWG |
| TSM-105-01-L-DV-A | CONN HEADER 10POS .100" DBL SMD |
| AD582KD | IC AMP SAMPLE HOLD 25MA 14CDIP |
| TMM-106-01-S-D-SM-P-TR | CONN HEADER 12POS DBL 2MM SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD204KY | 功能描述:IC AMP ISOL 5KHZ QUAD LP 38SIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:TS1854A View All Specifications 标准包装:50 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.25 V/µs 增益带宽积:630kHz -3db带宽:- 电流 - 输入偏压:16nA 电压 - 输入偏移:1000µV 电流 - 电源:162µA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):1.8 V ~ 6 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 |
| AD205-00E | 功能描述:SENSOR MAG SW 40G STANDRD 8-MSOP 制造商:nve corp/sensor products 系列:AD 包装:管件 零件状态:有效 功能:全极开关 技术:霍尔效应 极化:任意一种 感应范围:±2.5mT 跳闸，±1.1mT 释放 测试条件:-40°C ~ 125°C 电压 - 电源:4.5 V ~ 30 V 电流 - 电源（最大值）:4.5mA 电流 - 输出（最大值）:20mA 输出类型:开路集电极 特性:- 工作温度:-40°C ~ 125°C（TA） 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商器件封装:8-MSOP 标准包装:1,000 |
| AD205-02E | 功能描述:SENSOR MAG SW 40G STANDARD 8SOIC 制造商:nve corp/sensor products 系列:AD 包装:管件 零件状态:有效 功能:全极开关 技术:霍尔效应 极化:任意一种 感应范围:±5mT 跳闸，±2.5mT 释放 测试条件:-40°C ~ 125°C 电压 - 电源:4.5 V ~ 30 V 电流 - 电源（最大值）:4.5mA 电流 - 输出（最大值）:20mA 输出类型:开路集电极 特性:- 工作温度:-40°C ~ 125°C（TA） 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SOIC 标准包装:1,000 |
| AD2051/1 | 制造商:Analog Devices 功能描述: |
| AD205MX-G50GLF | 制造商:ADDA USA Corporation 功能描述:AD Series 20 x 20 x 6 mm 5 V 2.3 CFM Hypro Bearing DC Fan |
发布紧急采购，3分钟左右您将得到回复。