- 您现在的位置：买卖IC网 > PDF目录11656 > AD2S80ATE (Analog Devices Inc)IC R/D CONV TRACKING 44-LCCC PDF资料下载
参数资料
| 型号： | AD2S80ATE |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC R/D CONV TRACKING 44-LCCC |
| 标准包装： | 1 |
| 类型： | R/D 转换器 |
| 输入类型： | 并联 |
| 输出类型： | 数字 |
| 接口： | 并联 |
| 电流 - 电源： | 30mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-CLCC |
| 供应商设备封装： | 44-CLCC |
| 包装： | 管件 |
AD2S80A
REV. B
–14–
OSCILLATOR
(e.g., OSC1758)
C3
R3
TWISTED PAIR SCREENED CABLE
RESOLVER
S2
S4
S3
S1
R1
R2
1
2
3
4
5
6
7
31
AD2S80A
REF I/P
COS I/P
ANALOG
GND
DIGITAL
GND
SIGNAL
GND
SIN I/P
POWER RETURN
Figure 7. Connecting the AD2S80A to a Resolver
CONNECTING THE RESOLVER
The recommended connection circuit is shown in Figure 7.
In cases where the reference phase relative to the input signals
from the resolver requires adjustment, this can be easily
achieved by varying the value of the resistor R2 of the HF filter
(see Figure 1).
Assuming that R1 = R2 = R and C1 = C2 = C
and Reference Frequency =
1
2
π RC
by altering the value of R2, the phase of the reference relative to
the input signals will change in an approximately linear manner
for phase shifts of up to 10 degrees.
Increasing R2 by 10% introduces a phase lag of 2 degrees.
Decreasing R2 by 10% introduces a phase lead of 2 degrees.
C
R
PHASE LEAD = ARC TAN
1
2 fRC
R
C
PHASE LAG = ARC TAN 2 fRC
Phase Shift Circuits
TYPICAL CIRCUIT CONFIGURATION
Figure 8 shows a typical circuit configuration for the AD2S80A
in a 12-bit resolution mode. Values of the external components
have been chosen for a reference frequency of 5 kHz and a
maximum tracking rate of 260 rps with a bandwidth of 520 Hz.
Placing the values for R4, R6, C4 and C5 in the equation for KA
gives a value of 1.67
× 106. The resistors are 0.125 W, 5% toler-
ance preferred values. The capacitors are 100 V ceramic, 10%
tolerance components.
For signal and reference voltages greater than 2 V rms a simple
voltage divider circuit of resistors can be used to generate the
correct signal level at the converter. Care should be taken to
ensure that the ratios of the resistors between the sine signal line
and ground and the cosine signal line and ground are the same.
Any difference will result in an additional position error.
For more information on resistive scaling of SIN, COS and
REFERENCE converter inputs refer to the application note,
“Circuit Applications of the 2S81 and 2S81 Resolver-to-Digital
Converters.”
RELIABILITY
The AD2S80A Mean Time Between Failures (MTBF) has been
calculated according to MIL-HDBK-217E, Figure 10 shows the
MTBF in hours in naval sheltered conditions for AD2S80A/
883B only.
C
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/26JG41HN | CONN PLUG 41POS STRAIGHT W/PINS |
| AD2S80ATD | IC R/D CONV TRACKING 40CDIP |
| AD2S80ASD | IC R/D CONV TRACKING 40CDIP |
| AD2S82ALP | IC R/D CONV TRACKING 44PLCC |
| AD2S80ALD | IC R/D CONV TRACKING 40CDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD2S80ATE/883B | 制造商:AD 制造商全称:Analog Devices 功能描述:Variable Resolution, Monolithic Resolver-to-Digital Converter |
| AD2S80ATE883B | 制造商:AD 制造商全称:Analog Devices 功能描述:Variable Resolution, Monolithic esolver-to-Digital Converter |
| AD2S80AUD | 功能描述:IC R/D CONV TRACKING 40CDIP RoHS:否 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG，串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 |
| AD2S80AUD/B | 制造商:Analog Devices 功能描述:2 ARC MIN HIREL MIL TEMP - Bulk |
| AD2S80AUE | 制造商:AD 制造商全称:Analog Devices 功能描述:Variable Resolution, Monolithic Resolver-to-Digital Converter |
发布紧急采购，3分钟左右您将得到回复。