- 您现在的位置：买卖IC网 > PDF目录379635 > AD402M96RSA-5 (Electronic Theatre Controls, Inc.) Low voltage operation is more suitable to be used on battery backup, portable electronic PDF资料下载
参数资料
| 型号： | AD402M96RSA-5 |
| 厂商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Low voltage operation is more suitable to be used on battery backup, portable electronic |
| 中文描述： | 低电压操作更适合于备用电池，使用便携式电子 |
| 文件页数： | 14/28页 |
| 文件大小： | 211K |
| 代理商： | AD402M96RSA-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Rev.1
Page 14
Notes :
1. AC measurements assume t
T
= 2ns.
2. An initial pause of 100
is required after power up, and it followed by a minimum of eight
initialization cycles (RAS - only refresh cycle or CAS - before - RAS refresh cycle). If the internal
refresh counter is used, a minimun of eight CAS - before - RAS refresh cycles are required.
3. In delayed write or read-modify-write cycles, OE must disable output buffer prior to applying data to
the device.
4. All the V
CC
and V
SS
pins shall be supplied with the same voltages.
5. t
RAS
(min) = t
RWD
(min)+t
RWL
(min)+t
T
in read-modify-write cycle.
6. t
CAS
(min) = t
CWD
(min)+t
CWL
(min)+t
T
in read-modify-write cycle.
7. t
ASC
(min), t
RCS
(min), t
WCS
(min), and t
RPC
are determined by the falling edge of CAS .
8. t
RCD
(max) is specified as a reference point only, and t
RAC
(max) can be met with the t
RCD
(max) limit.
Otherwise, t
RAC
is controlled exclusively by t
CAC
if t
RCD
is greater than the specified t
RCD
(max) limit.
9. t
RAD
(max) is specified as a reference point only, and t
RAC
(max) can be met with the t
RAD
(max) limit.
Otherwise, t
RAC
is controlled exclusively by t
AA
if t
RAD
is greater than the specified t
RAD
(max) limit.
10. t
CRP
, t
CHR
, t
RCH
, t
CPA
and t
CPW
are determined by the rising edge of CAS .
11. V
IH
(min) and V
IL
(max) are reference levels for measuring timing or input signals. Therefore, transition
time is measured between V
IH
and V
IL
.
12. Assumes that t
RCD
t
RCD
(max) and t
RAD
t
RAD
(max). If t
RCD
or t
RAD
is greater than the maximum
recommended value shown in this table, t
RAC
exceeds the value shown.
≥
13. Assumes that
(max) and
(max).
14. Access time is determined by the maximum of t
AA
, t
CAC
, t
CPA
.
15. Assumes that
(max) and
(max).
16. Either t
RCH
or t
RRH
must be satisfied for a read cycle.
17. t
OFF
(max) and t
OEZ
(max) define the time at which the output achieves the open circuit condition (high
impedance). t
OFF
is determined by the later rising edge of RAS or CAS.
18. t
WCS
, t
RWD
, t
CWD
, and t
AWD
are not restrictive operating parameters. They are included in the data
sheet as electrical characteristics only. If
(min), the cycle is an early write cycle and the
data out will remain open circuit (high impedance) throughout the entire cycle. If
(min),
(min),
(min) and
(min), the cycle is a read-modify-write and
the data output will contain data read from the selected cell. If neither of the above sets of conditions
is satisfied, the condition of the data output (at access time) is indeterminate.
19. These parameters are referenced to CAS separately in an early write cycle and to WE edge in a
delayed write or a read-modify-write cycle.
20. t
RASP
defines RAS pulse width in EDO page mode cycles.
μ
s
≤
≤
t
RCD
t
RCD
t
RAD
t
RAD
≤
t
RCD
t
RCD
≤
t
RAD
t
RAD
≥
t
WCS
t
WCS
≥
t
RWD
t
RWD
≥
t
CWD
t
CWD
≥
t
AWD
t
AWD
≥
t
CPW
t
CPW
≥
相关PDF资料 |
PDF描述 |
|---|---|
| AD401M96RSA-5 | Low voltage operation is more suitable to be used on battery backup, portable electronic |
| AD4016M166RSA-5 | Low voltage operation is more suitable to be used on battery backup, portable electronic |
| AD408M166RSA-5 | Low voltage operation is more suitable to be used on battery backup, portable electronic |
| AD404M166RSA-5 | Low voltage operation is more suitable to be used on battery backup, portable electronic |
| AD402M166RSA-5 | Low voltage operation is more suitable to be used on battery backup, portable electronic |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD-4030-CUTTER/STRIPPE | 制造商:TE Connectivity 功能描述:AD-4030-CUTTER/STRIPPER |
| AD-4030-CUTTER/STRIPPER | 功能描述:手工工具 AD-4030-CUTTER/STRIPPER RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| AD40321 | 制造商:Analog Devices 功能描述:40321 |
| AD404-00E | 功能描述:SENSOR MAG SW 20G STANDRD 8-MSOP 制造商:nve corp/sensor products 系列:AD 包装:管件 零件状态:有效 功能:全极开关 技术:霍尔效应 极化:任意一种 感应范围:±2.5mT 跳闸，±1.1mT 释放 测试条件:-40°C ~ 125°C 电压 - 电源:4.5 V ~ 30 V 电流 - 电源（最大值）:4.5mA 电流 - 输出（最大值）:20mA 输出类型:开路集电极 特性:- 工作温度:-40°C ~ 125°C（TA） 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商器件封装:8-MSOP 标准包装:1,000 |
| AD404-02E | 功能描述:SENSOR MAG SW 20G STANDARD 8SOIC 制造商:nve corp/sensor products 系列:AD 包装:管件 零件状态:有效 功能:全极开关 技术:霍尔效应 极化:任意一种 感应范围:±2.5mT 跳闸，±1.1mT 释放 测试条件:-40°C ~ 125°C 电压 - 电源:4.5 V ~ 30 V 电流 - 电源（最大值）:4.5mA 电流 - 输出（最大值）:20mA 输出类型:开路集电极 特性:- 工作温度:-40°C ~ 125°C（TA） 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SOIC 标准包装:1,000 |
发布紧急采购，3分钟左右您将得到回复。