参数资料
| 型号： | AD421BRRL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/14页 |
| 文件大小： | 0K |
| 描述： | IC DAC SNGL 16BIT 16-SOIC T/R |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 标准包装： | 400 |
| 设置时间： | 8ms |
| 位数： | 16 |
| 数据接口： | 串行 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 450mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 1 电流，单极 |
AD421
–8–
REV. C
WORD "N"
01
10 0
11
0
00
0
00
CLOCK
DATA
(MSB)
(LSB)
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
LATCH
B16
XX X X X X X
X
Figure 7. Write Cycle for Programming Alarm Current
Data
MICROPROCESSOR INTERFACING
AD421 – MC68HC11 (SPI BUS) INTERFACE
Figure 8 shows a typical interface between the AD421 and the
Motorola MC68HC11 SPI (Serial Peripheral Interface) bus.
The SCK, MOSI and SS pins of the 68HC11 are respectively
connected to the CLOCK, DATA IN and LATCH pins of the
AD421.
SCK
MOSI
SS
CLOCK
DATA IN
LATCH
AD421*
68HC11
* ADDITIONAL PINS OMITTED FOR CLARITY
Figure 8. AD421 to 68HC11 Interface
A typical routine such as the one shown below begins by initializ-
ing the state of the various SPI data and control registers.
INIT
LDAA #$2F
;
SS = 1; SCK = 0; MOSI = 1
STAA
PORTD
;SEND TO SPI OUTPUTS
LDAA #$38
;
SS, SCK, MOSI = OUTPUTS
STAA
DDRD
;SEND DATA DIRECTION INFO
LDAA #$50
;DABL INTRPTS, SPI IS MASTER & ON
STAA
SPCR
;CPOL = 0, CPHA = 0, 1MHZ BAUDRATE
NEXTPT LDAA MSBY
;LOAD ACCUM W/UPPER 8 BITS
BSR
SENDAT ;JUMP TO DAC OUTPUT ROUTINE
JMP
NEXTPT ;INFINITE LOOP
SENDAT LDY
#$1000
;POINT AT ON-CHIP REGISTERS
BCLR
$08,Y,$20 ;DRIVE
SS (LATCH) LOW
STAA
SPDR
;SEND MS-BYTE TO SPI DATA REG
WAIT1
LDAA SPSR
;CHECK STATUS OF SPIE
BPL
WAIT1
;POLL FOR END OF X-MISSION
LDAA LSBY
;GET LOW 8 BITS FROM MEMORY
STAA
SPDR
;SEND LS-BYTE TO SPI DATA REG
WAIT2
LDAA SPSR
;CHECK STATUS OF SPIE
BPL
WAIT2;
;POLL FOR END OF X-MISSION
BSET
$08,Y,$20 ;DRIVE
SS HIGH TO LATCH DATA
RTS
The SPI data port is configured to process data in 8-bit bytes.
The most significant data byte (MSBY) is retrieved from
memory and processed by the SENDAT routine. The SS pin is
driven low by indexing into the PORTD data register and clear
Bit 5. The MSBY is then sent to the SPI data register where it is
automatically transferred to the AD421 internal shift resistor.
of 11.147 mA. With 16 clock pulses between consecutive latch
signals data written is for normal 4 mA to 20 mA operation.
Table II. Ideal Input/Output Code Table
for 4 mA to 20 mA Operation
Code
Output Current
0000 0000 0000 0000
4 mA
0000 0000 0000 0001
4.000244 mA
0000 0000 0000 0010
4.000488 mA
0100 0000 0000 0000
8 mA
1000 0000 0000 0000
12 mA
1100 0000 0000 0000
16 mA
1111 1111 1111 1101
19.999268 mA
1111 1111 1111 1110
19.999512 mA
1111 1111 1111 1111
19.999756 mA
WORD "N"
WORD "N +1"
10
1 1
1
11 1
1
00
0
0 0
10 0
1
CLOCK
DATA
(MSB)
(LSB)
B15
B14
B13
B12
B1
1
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
B15
B14
B13
B12
LATCH
Figure 6. Write Cycle for 4 mA to 20 mA Operation
Alarm Current Coding
Table III shows the ideal input-code-to-output-current relation-
ship for alarm current programming of the AD421. In this case,
the equivalent span is 0 mA to 32 mA but a reliable operating
span is 3.5 mA to 24 mA. The part may give an indeterminate
output for code values outside the range given in the table. As a
result, the user is advised to restrict the code programmed to the
part in alarm current mode to within the range shown in Table
III. Figure 7 shows a timing diagram for loading an alarm cur-
rent of 3.75 mA to the AD421 with an 8-bit microcontroller
using three 8-bit writes.
The output current values shown assume a REF IN voltage of
+2.5 V. With a REF IN of +2.5 V, an ideal 1 LSB = 32 mA/
131,072 = 244 nA.
Table III. Ideal Input/Output Code Table
for Alarm Current Operation
Code
Output Current
0 0011 1000 0000 0000
3.5 mA
0 0011 1100 0000 0000
3.75 mA
0 0100 0000 0000 0000
4 mA
0 1000 0000 0000 0000
8 mA
1 0000 0000 0000 0000
16 mA
1 0100 0000 0000 0000
20 mA
1 0110 0000 0000 0000
22 mA
1 1000 0000 0000 0000
24 mA
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2WB-IV-F4 | CONVERTER MOD DC/DC 95V 150W |
| LTC1650CN#PBF | IC D/A CONV 16BIT R-R 16-DIP |
| VE-B5W-MV-B1 | CONVERTER MOD DC/DC 5.5V 150W |
| VE-B5R-MV-B1 | CONVERTER MOD DC/DC 7.5V 150W |
| VE-25L-IV-F2 | CONVERTER MOD DC/DC 28V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD421BRURL | 制造商:未知厂家 制造商全称:未知厂家 功能描述:16-Bit Digital-to-Analog Converter |
| AD421BRZ | 功能描述:IC DAC SRL 16BIT 16-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| AD421BRZRL | 功能描述:IC DAC 16BIT LOOP 4-20MA 16SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
| AD421BRZRL7 | 功能描述:IC DAC 16BIT LOOP 4-20MA 16SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 设置时间:4µs 位数:12 数据接口:串行 转换器数目:2 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-uMAX 包装:管件 输出数目和类型:2 电压，单极 采样率（每秒）:* 产品目录页面:1398 (CN2011-ZH PDF) |
| AD422-00E | 功能描述:SENSOR MAG SW 40G CROS AX 8-MSOP 制造商:nve corp/sensor products 系列:AD 包装:管件 零件状态:有效 功能:全极开关 技术:霍尔效应 极化:任意一种 感应范围:±5mT 跳闸，±2.5mT 释放 测试条件:-40°C ~ 125°C 电压 - 电源:4.5 V ~ 30 V 电流 - 电源（最大值）:4.5mA 电流 - 输出（最大值）:20mA 输出类型:开路集电极 特性:- 工作温度:-40°C ~ 125°C（TA） 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商器件封装:8-MSOP 标准包装:1,000 |
发布紧急采购，3分钟左右您将得到回复。