参数资料
| 型号： | AD5116BCPZ5-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 64POS 5K 8LFCSP |
| 标准包装： | 3,000 |
| 接片： | 64 |
| 电阻（欧姆）： | 5k |
| 电路数： | 1 |
| 温度系数： | 标准值 35 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 2 线按钮 |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-UFDFN 裸露焊盘，CSP |
| 供应商设备封装： | 8-LFCSP-UD（2x2） |
| 包装： | 带卷 (TR) |
Data Sheet
AD5116
Rev. B | Page 15 of 16
PROGRAMMING THE POTENTIOMETER DIVIDER
Voltage Output Operation
The digital potentiometer easily generates a voltage divider at
wiper-to-B and wiper-to-A that is proportional to the input
voltage at A to B, as shown in Figure 43. Unlike the polarity of
VDD to GND, which must be positive, voltage across A-to-B, W-
to-A, and W-to-B can be at either polarity.
09657-
041
W
A
B
VIN
VOUT
Figure 43. Potentiometer Mode Configuration
If ignoring the effect of the wiper resistance for simplicity,
connecting Terminal A to 5 V and Terminal B to ground
produces an output voltage at the Wiper W to Terminal B
ranging from 0 V to 5 V. The general equation defining the
output voltage at VW, with respect to ground for any valid
input voltage applied to Terminal A and Terminal B, is:
B
AB
AW
A
AB
WB
W
V
R
D
R
V
R
D
R
D
V
×
+
×
=
)
(
)
(
)
(
(6)
where:
RWB(D) can be obtained from Equation 1 or Equation 2.
RAW(D) can be obtained from Equation 3 to Equation 5 .
Operation of the digital potentiometer in the divider mode
results in a more accurate operation over temperature. Unlike
the rheostat mode, the output voltage is dependent mainly
on the ratio of the internal resistors, RWA and RWB, and not the
absolute values. Therefore, the temperature drift reduces to
5 ppm/°C.
TERMINAL VOLTAGE OPERATING RANGE
The AD5116 is designed with internal ESD diodes for
protection. These diodes also set the voltage boundary of
the terminal operating voltages. Positive signals present on
Terminal A, Terminal B, or Terminal W that exceed VDDare
clamped by the forward-biased diode. There is no polarity
constraint between VA, VW, and VB, but they cannot be higher
than VDDor lower than GND.
POWER-UP SEQUENCE
Because of the ESD protection diodes that limit the voltage
compliance at Terminal A, Terminal B, and Terminal W (see
any voltage to Terminal A, Terminal B, and Terminal W.
Otherwise, the diodes are forward-biased such that VDD is
powered on unintentionally and can affect other parts of the
circuit. Similarly, VDD should be powered down last. The ideal
power-on sequence is in the following order: GND, VDD, and
VA/VB/VW. The order of powering VA, VB, and VW is not
important as long as they are powered on after VDD. The
states of the PU and PD pins can be logic low or floating,
but they should not be logic high during power-on.
GND
09657-
042
VDD
A
W
B
Figure 44. Maximum Terminal Voltages Set by VDD and VSS
LAYOUT AND POWER SUPPLY BIASING
It is always a good practice to use compact, minimum lead
length layout design. The leads to the input should be as direct
as possible with a minimum conductor length. Ground paths
should have low resistance and low inductance. It is also good
practice to bypass the power supplies with quality capacitors.
Low equivalent series resistance (ESR) 1 μF to 10 μF tantalum
or electrolytic capacitors should be applied at the supplies to
minimize any transient disturbance and to filter low frequency
ripple. Figure 45 illustrates the basic supply bypassing config-
uration for the AD5116.
09657-
043
AD5116
C2
10F
C1
0.1F
VDD
AGND
GND
+
Figure 45. Power Supply Bypassing
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/24FG16PC | CONN RCPT 16POS JAM NUT W/PINS |
| AD5245BRJZ10-RL7 | IC DGTL POT 256POS SOT-23-8 T/R |
| AD5258BRMZ1-R7 | IC POT DGTL I2C 1K 64P 10MSOP |
| D38999/24FG16PB | CONN RCPT 16POS JAM NUT W/PINS |
| AD5258BRMZ10-R7 | IC POT DGTL I2C 10K 64P 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5116BCPZ80-500R7 | 功能描述:IC DGTL POT 64POS 80K 8LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD5116BCPZ80-RL7 | 功能描述:IC DGTL POT 64POS 80K 8LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD5121 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single Channel, 128-/256-Position, I2C/SPI, Nonvolatile Digital Potentiometer |
| AD5121BCPZ100-RL7 | 制造商:Analog Devices 功能描述:Digital Potentiometer 128POS 100KOhm Single 16-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:128TAP, SINGLE DIGIPOT, NVM, SPI/I2C - Tape and Reel 制造商:Analog Devices 功能描述:POT DIG NV 128 100K 16LFC 制造商:Analog Devices 功能描述:POT, DIG, NV, 128, 100K, 16LFCSP 制造商:Analog Devices Inc. 功能描述:Digital Potentiometer ICs 128tap Single DigiPOT NVM SPI/I2C 制造商:Analog Devices 功能描述:DIGITAL POT, 100KOHM, SINGLE, LFCSP-16; End To End Resistance:100kohm; Track Taper:Logarithmic; Resistance Tolerance: 8%; Supply Voltage Min:1.8V; Supply Voltage Max:5.5V; Potentiometer IC Case Style:LFCSP; No. of Pins:16 ;RoHS Compliant: Yes 制造商:Analog Devices 功能描述:DIGITAL POTENTIOMETER |
| AD5121BCPZ10-RL7 | 制造商:Analog Devices 功能描述:Digital Potentiometer 128POS 10KOhm Single 16-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:128TAP, SINGLE DIGIPOT, NVM, SPI/I2C - Tape and Reel 制造商:Analog Devices 功能描述:IC DGTL POT 128POS 10K 16LFCSP 制造商:Analog Devices Inc. 功能描述:Digital Potentiometer ICs 128-pos SGL NVM SPI/I2C 制造商:Analog Devices Inc. 功能描述:Digital Potentiometer ICs 128tap Single DigiPOT NVM SPI/I2C 制造商:Analog Devices 功能描述:DIGITAL POTENTIOMETER |
发布紧急采购，3分钟左右您将得到回复。