参数资料
型号: AD5170BRMZ2.5
厂商: Analog Devices Inc
文件页数: 7/24页
文件大小: 0K
描述: IC POT DGTL 2.5K 256POS 10-MSOP
标准包装: 50
接片: 256
电阻(欧姆): 2.5k
电路数: 1
温度系数: 标准值 35 ppm/°C
存储器类型: 易失
接口: I²C,2 线串口
电源电压: 2.7 V ~ 5.5 V
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 10-TFSOP,10-MSOP(0.118",3.00mm 宽)
供应商设备封装: 10-MSOP
包装: 管件
AD5170
Rev. G | Page 15 of 24
THEORY OF OPERATION
04
10
4-
0
22
SDA
SCL
A
W
B
COMPARATOR
MUX
DECODER
FUSES
EN
FUSE
REG.
DAC
REG.
I2C INTERFACE
ONE-TIME
PROGRAM/TEST
CONTROL BLOCK
Figure 33. Detailed Functional Block Diagram
The AD5170 is a 256-position, digitally controlled, variable
resistor (VR) that employs fuse link technology to achieve
memory retention of the resistance setting.
An internal power-on preset places the wiper at midscale during
power-on. If the OTP function is activated, the device powers
up at the user-defined permanent setting.
ONE-TIME PROGRAMMING (OTP)
Prior to OTP activation, the AD5170 presets to midscale during
initial power-on. After the wiper is set at the desired position,
the resistance can be permanently set by programming the T bit
high along with the proper coding (see Table 9 and Table 10) and
one-time VDD_OTP. Note that fuse link technology of the AD517x
family of digital potentiometers requires that VDD_OTP between 5.6 V
and 5.8 V blow the fuses to achieve a given nonvolatile setting. On
the other hand, VDD can be 2.7 V to 5.5 V during operation. For
system supplies that are lower than 5.6 V, an external supply for
one-time programming is required. Note that the user is allowed
only one attempt in blowing the fuses. If the user fails to blow the
fuses at the first attempt, the structures of the fuses may have
changed such that they can never be blown, regardless of the
energy applied at subsequent events. For details, see the Power
The device control circuit has two validation bits, E1 and E0,
that can be read back to check the programming status (see
Table 6). Users should always read back the validation bits to
ensure that the fuses are properly blown. After the fuses are
blown, all fuse latches are enabled upon subsequent power-on;
therefore, the output corresponds to the stored setting. Figure 33
shows a detailed functional block diagram.
Table 6. Validation Status
E1
E0
Status
0
Ready for programming.
1
0
Fatal error. Some fuses are not blown. Do not retry.
Discard this unit.
1
Successful. No further programming is possible.
PROGRAMMING THE VARIABLE RESISTOR AND
VOLTAGE—RHEOSTAT OPERATION
The nominal resistance (RAB) between Terminal A and Terminal B
is available in 2.5 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ. The nominal
resistance of the VR has 256 contact points that are accessed by
the wiper terminal, plus the B terminal contact. The 8-bit data
in the RDAC latch is decoded to select one of the 256 possible
settings.
A
W
B
A
W
B
A
W
B
0
41
04
-0
24
Figure 34. Rheostat Mode Configuration
Assuming that a 10 kΩ part is used, the first connection of the
wiper starts at Terminal B for Data 0x00. Because there is a 50 Ω
wiper contact resistance, such a connection yields a minimum of
100 Ω (2 × 50 Ω) resistance between Terminal W and Terminal B.
The second connection is the first tap point, which corresponds
to 139 Ω (RWB = RAB/256 + 2 × RW = 39 Ω + 2 × 50 Ω) for Data
0x01. The third connection is the next tap point, representing
178 Ω (2 × 39 Ω + 2 × 50 Ω) for Data 0x02, and so on. Each LSB
data value increase moves the wiper up the resistor ladder until
the last tap point is reached at 10,100 Ω (RAB + 2 × RW).
相关PDF资料
PDF描述
DS1020S-100+ IC DELAY LINE 256TAP 16-SOIC
DS1135LU-15+ IC DELAY LINE 15NS 8-USOP
DS1135LZ-20+ IC DELAY LINE 20NS 8-SOIC
VE-B4Z-MY-F4 CONVERTER MOD DC/DC 2V 20W
AD5170BRMZ10 IC POT DGTL 10K 256POS 10-MSOP
相关代理商/技术参数
参数描述
AD5170BRMZ50 功能描述:IC POT DGTL 50K 256POS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,300 系列:WiperLock™ 接片:257 电阻(欧姆):100k 电路数:1 温度系数:标准值 150 ppm/°C 存储器类型:易失 接口:3 线 SPI(芯片选择) 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VDFN 裸露焊盘 供应商设备封装:8-DFN-EP(3x3) 包装:带卷 (TR)
AD5170BRMZ50-RL7 功能描述:IC DGTL POT 256POS 50K 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻(欧姆):10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行(芯片选择,递增,增/减) 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN(2x3) 包装:带卷 (TR)
AD5170EVAL 制造商:Analog Devices 功能描述:DEV TOOLS 256-POSITION TWO-TIME PROGRAMMABLE I2C DGTL POTENT - Bulk
AD5171 制造商:AD 制造商全称:Analog Devices 功能描述:64-Position OTP Digital Potentiometer
AD5171BRJ10 制造商:Analog Devices 功能描述:DGTL POTENTIOMETER 64POS 10KOHM SGL 8PIN SOT-23 - Bulk