- 您现在的位置：买卖IC网 > PDF目录1889 > AD5174BRMZ-10-RL7 (Analog Devices Inc)IC DGTL POT 1024POS 10K 10MSOP PDF资料下载
参数资料
| 型号： | AD5174BRMZ-10-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 4/20页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 1024POS 10K 10MSOP |
| 产品变化通告： | AD5174 Pin Requirement 14/Dec/2010 |
| 标准包装： | 1,000 |
| 接片： | 1024 |
| 电阻（欧姆）： | 10k |
| 电路数： | 1 |
| 温度系数： | 标准值 35 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 4 线串行 |
| 电源电压： | 2.7 V ~ 5.5 V，±2.5 V ~ 2.75 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 带卷 (TR) |
AD5174
Rev. B | Page 12 of 20
THEORY OF OPERATION
The AD5174 is designed to operate as a true variable resistor for
analog signals within the terminal voltage range of VSS < VTERM
< VDD. The RDAC register contents determine the resistor wiper
position. The RDAC register acts as a scratchpad register, which
allows unlimited changes of resistance settings. The RDAC register
can be programmed with any position setting by using the SPI
interface. When a desirable wiper position is found, this value
can be stored in a 50-TP memory register. Thereafter, the wiper
position is always restored to that position for subsequent
power-ups. The storing of 50-TP data takes approximately 350 ms;
during this time, the AD5174 locks to prevent any changes from
taking place.
The AD5174 also feature a patented 1% end-to-end resistor
tolerance. This simplifies precision, rheostat mode, and open-
loop applications where knowledge of absolute resistance is
critical.
SERIAL DATA INTERFACE
The AD5174 contains a serial interface (SYNC, SCLK, DIN,
and SDO) that is compatible with SPI interface standards, as well
as most DSPs. This device allows writing of data via the serial
interface to every register.
SHIFT REGISTER
The shift register is 16 bits wide, as shown in Figure 2. The
16-bit word consists of two unused bits, which should be set to
0, followed by four control bits and 10 RDAC data bits. Data is
loaded MSB first (Bit D9). The four control bits determine the
shows a timing diagram of a typical AD5174 write sequence.
The write sequence begins by bringing the SYNC line low. The
SYNC pin must be held low until the complete data-word is
loaded from the DIN pin. When SYNC returns high, the serial
data-word is decoded according to the instructions in
.
The command bits (Cx) control the operation of the digital
potentiometer. The data bits (Dx) are the values that are loaded
into the decoded register. The AD5174 has an internal counter
that counts a multiple of 16 bits (a frame) for proper operation.
For example, AD5174 works with a 32-bit word but does not
work properly with a 31-bit or 33-bit word. The AD5174
does not require a continuous SCLK when
SYNC is high.
To minimize power consumption in the digital input buffers,
operate all serial interface pins close to the VDD supply rails.
RDAC REGISTER
The RDAC register directly controls the position of the digital
rheostat wiper. For example, when the RDAC register is loaded
with all 0s, the wiper is connected to Terminal A of the variable
resistor. The RDAC register is a standard logic register, and there
is no restriction on the number of changes allowed. The basic
mode of setting the variable resistor wiper position (programming
the RDAC register) is accomplished by loading the serial data
input register with Command 1 (see Table 6) and with the desired
wiper position data.
50-TP MEMORY BLOCK
The AD5174 contains an array of 50-TP programmable memory
registers, which allow the wiper position to be programmed up
to 50 times. Table 10 shows the memory map. When the desired
wiper position is determined, the user can load the serial data
input register with Command 3 (see Table 6), which stores the
wiper position data in a 50-TP memory register. The first address
to be programmed is Location 0x01 (see Table 10); the AD5174
increments the 50-TP memory address for each subsequent
program until the memory is full. Programming data to 50-TP
consumes approximately 4 mA for 55 ms, and takes approx-
imately 350 ms to complete, during which time the shift register
locks to prevent any changes from occurring. Bit C2 of the
control register can be polled to verify that the fuse program
command was completed properly. No change in supply voltage
is required to program the 50-TP memory; however, a 1 μF
capacitor on the EXT_CAP pin is required (see Figure 28).
Prior to 50-TP activation, the AD5174 presets to midscale
on power-up.
WRITE PROTECTION
At power-up, the serial data input register write commands for
both the RDAC register and the 50-TP memory registers are
disabled. The RDAC write protect bit, C1, of the control register
change of the RDAC register content regardless of the software
commands, except that the RDAC register can be refreshed
from the 50-TP memory using the software reset, Command 4
(see Table 6). To enable programming of the RDAC register,
the write protect bit (Bit C1), of the control register must first
be programmed by loading the serial data input register with
Command 7. To enable programming of the 50-TP memory,
the program enable bit (Bit C0) of the control register, which
is set to 0 by default, must first be set to 1.
相关PDF资料 |
PDF描述 |
|---|---|
| AD5175BRMZ-10-RL7 | IC DGTL POT 1024POS 10K 10MSOP |
| AD5200BRMZ50-REEL7 | IC POT DGTL 50K 256POS 10MSOP |
| AD5203ARZ100 | IC POT DGTL QUAD 64POS 24SOIC |
| AD5204BRZ50 | IC DGTL POT QUAD 50K 24-SOIC |
| AD5207BRU50 | IC DGTL POT DUAL 256POS 14TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5175 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Channel, 1024-Position, Digital Rheostat with I2C Interface and 50-TP Memory |
| AD5175BCPZ-10-R2 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Channel, 1024-Position, Digital Rheostat with I2C Interface and 50-TP Memory |
| AD5175BCPZ-10-RL7 | 功能描述:IC RHEOSTAT 5V 50-TP 1024 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD5175BRMZ-10 | 功能描述:IC DGTL POT 1024POS 10K 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,300 系列:WiperLock™ 接片:257 电阻（欧姆）:100k 电路数:1 温度系数:标准值 150 ppm/°C 存储器类型:易失 接口:3 线 SPI（芯片选择） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VDFN 裸露焊盘 供应商设备封装:8-DFN-EP（3x3） 包装:带卷 (TR) |
| AD5175BRMZ-10-RL7 | 功能描述:IC DGTL POT 1024POS 10K 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。