- 您现在的位置：买卖IC网 > PDF目录9314 > AD5247BKSZ100-RL7 (Analog Devices Inc)IC POT DGTL 100K 128POS SC70-6 PDF资料下载
参数资料
| 型号： | AD5247BKSZ100-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL 100K 128POS SC70-6 |
| 标准包装： | 1 |
| 接片： | 128 |
| 电阻（欧姆）： | 100k |
| 电路数： | 1 |
| 温度系数： | 标准值 45 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | I²C |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-TSSOP，SC-88，SOT-363 |
| 供应商设备封装： | SC-70-6 |
| 包装： | 标准包装 |
| 配用： | AD5247EVAL-ND - BOARD EVAL FOR AD5247 |
| 其它名称： | AD5247BKSZ100-RL7DKR |
AD5247
Data Sheet
Rev. F | Page 14 of 20
THEORY OF OPERATION
The AD5247 is a 128-position, digitally-controlled variable
resistor (VR) device. An internal power-on preset places the
wiper at midscale during power-on, which simplifies the
default condition recovery at power-up.
PROGRAMMING THE VARIABLE RESISTOR
Rheostat Operation
The nominal resistance (RAB) of the RDAC between Terminal A
and Terminal B is available in 5 k, 10 k, 50 k, and 100 k. The
final two or three digits of the part number determine the nominal
resistance value; for example, 10 k = 10 and 50 k = 50. The
RAB of the VR has 128 contact points accessed by the wiper
terminal, plus the B terminal contact. The 7-bit data in the
RDAC latch is decoded to select one of the 128 possible settings.
Assuming a 10 k part is used, the wiper’s first connection starts
at the B terminal for Data 0x00. Because there is a 50 wiper
contact resistance, such a connection yields a minimum of 100
(2 × 50 ) resistance between Terminal W and Terminal B. The
second connection is the first tap point, corresponding to 178
(RWB = RAB/128 + RW = 78 + 2 × 50 ) for Data 0x01. The third
connection is the next tap point, representing 256 (2 × 78
+ 2 × 50 ) for Data 0x02, and so on. Each LSB data value increase
moves the wiper up the resistor ladder until the last tap point is
reached at 10,100 (RAB + 2 × RW).
Figure 35 shows a simplified diagram of the equivalent RDAC
circuit where the last resistor string is not accessed.
Bx
Wx
Ax
D6
D4
D5
D2
D3
D1
D0
RDAC
LATCH
AND
DECODER
RS
03876-
034
Figure 35. AD5247 Equivalent RDAC Circuit
The general equation determining the digitally programmed
output resistance between W and B is
W
AB
WB
R
D
(D)
R
×
+
×
=
2
128
(1)
where:
D is the decimal equivalent of the binary code loaded in the
7-bit RDAC register.
RAB is the end-to-end resistance.
RW is the wiper resistance contributed by the on resistance of
the internal switch.
In summary, if RAB = 10 k and the Terminal A is open-circuited,
RDAC latch codes.
Table 9. Codes and Corresponding RWB Resistance
D (Decimal)
RWB ()
Output State
127
10,072
Full scale (RAB + 2 × RW)
64
5150
Midscale
1
228
1 LSB
0
150
Zero scale (wiper contact resistance)
Note that in the zero-scale condition, a finite resistance of
100 between Terminal W and Terminal B is present. Care
should be taken to limit the current flow between W and B in
this state to a maximum pulse current of no more than 20 mA.
Otherwise, degradation or possible destruction of the internal
switch contact can occur.
Similar to the mechanical potentiometer, the resistance of
the RDAC between Wiper W and Terminal A also produces a
digitally controlled complementary resistance, RWA. When
these terminals are used, the Terminal B can be opened. Set the
resistance value for RWA to start at a maximum value of resistance
and to decrease the data loaded in the latch increases in value.
The general equation for this operation is
W
AB
WA
R
D
(D)
R
×
+
×
=
2
128
(2)
If RAB = 10 k and the B terminal is open-circuited, the output
latch codes.
Table 10. Codes and Corresponding RWA Resistance
D (Decimal)
RWA ()
Output State
127
228
Full scale
64
5150
Midscale
1
10,071
1 LSB
0
10,150
Zero scale
Typical device-to-device matching is process lot dependent
and can vary by up to ±30%. Because the resistance element
is processed in thin film technology, the change in RAB with
temperature has a very low 45 ppm/°C temperature coefficient.
相关PDF资料 |
PDF描述 |
|---|---|
| DS2415X | IC TIME CHIP 1-WIRE CSP |
| DS2417P/T&R | IC TIMECHIP W/INTRPT 1WIRE 6TSOC |
| VI-BN2-IU-F2 | CONVERTER MOD DC/DC 15V 200W |
| AD5247BKSZ5-RL7 | IC POT DGTL 5K 128POS SC70-6 |
| DS1501WSN | IC RTC WDOG Y2KC 3.3V IND 28SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5247BKSZ10-1RL7 | 制造商:Analog Devices 功能描述:128-POSITION I2C?-COMPATIBLE DIGITAL POTENTIOMETER - Tape and Reel 制造商:Analog Devices 功能描述:ANAAD5247BKSZ10-1RL7 7-BIT I2C DIGIPOT |
| AD5247BKSZ10-2RL7 | 功能描述:IC DGTL POT 128POS 10K SC70-6 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5247BKSZ10-RL7 | 功能描述:IC POT DGTL 10K 128POS SC70-6 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5247BKSZ50-RL7 | 功能描述:IC POT DGTL 50K 128POS SC70-6 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5247BKSZ5-RL7 | 功能描述:IC POT DGTL 5K 128POS SC70-6 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。