- 您现在的位置：买卖IC网 > PDF目录9430 > AD5248BRMZ50 (Analog Devices Inc)IC DGTL POT DUAL 50K I2C 10-MSOP PDF资料下载
参数资料
| 型号： | AD5248BRMZ50 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 5/20页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT DUAL 50K I2C 10-MSOP |
| 标准包装： | 50 |
| 接片： | 256 |
| 电阻（欧姆）： | 50k |
| 电路数： | 2 |
| 温度系数： | 标准值 35 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 管件 |
| 产品目录页面： | 787 (CN2011-ZH PDF) |
| 配用： | AD5248EVAL-ND - BOARD EVAL FOR AD5248 |
Data Sheet
AD5243/AD5248
Rev. B | Page 13 of 20
THEORY OF OPERATION
The AD5243/AD5248 are 256-position, digitally controlled
variable resistor (VR) devices.
An internal power-on preset places the wiper at midscale
during power-on, which simplifies the fault condition recovery
at power-up.
PROGRAMMING THE VARIABLE RESISTOR AND
VOLTAGE
Rheostat Operation
The nominal resistance of the RDAC between Terminal A and
Terminal B is available in 2.5 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ.
The nominal resistance (RAB) of the VR has 256 contact points
accessed by the wiper terminal and the B terminal contact. The
8-bit data in the RDAC latch is decoded to select one of the 256
possible settings.
A
W
B
A
W
B
A
W
B
04109-0-012
Figure 37. Rheostat Mode Configuration
Assuming that a 10 kΩ part is used, the first connection of the
wiper starts at the B terminal for Data 0x00. Because there is
a 160 Ω wiper contact resistance, such a connection yields a
minimum of 320 Ω (2 × 160 Ω) resistance between Terminal W
and Terminal B. The second connection is the first tap point,
which corresponds to 359 Ω (RWB = RAB/256 + 2 × RW = 39 Ω +
2 × 160 Ω) for Data 0x01. The third connection is the next tap
point, representing 398 Ω (2 × 39 Ω + 2 × 160 Ω) for Data 0x02,
and so on. Each LSB data value increase moves the wiper up the
resistor ladder until the last tap point is reached at 10,281 Ω
(RAB + 2 × RW).
D5
D4
D3
D7
D6
D2
D1
D0
RDAC
LATCH
AND
DECODER
RS
A
W
B
04109-0-013
Figure 38. AD5243 Equivalent RDAC Circuit
The general equation determining the digitally programmed
output resistance between W and B is
W
AB
WB
R
D
R
2
256
)
(
(1)
where:
D
is the decimal equivalent of the binary code loaded in the
8-bit RDAC register.
RAB
is the end-to-end resistance.
RW
is the wiper resistance contributed by the on resistance of
the internal switch.
In summary, if RAB is 10 kΩ and the A terminal is open circuited,
the following output resistance, RWB, is set for the indicated
RDAC latch codes.
Table 7. Codes and Corresponding RWB Resistance
D (Dec)
RWB (Ω)
Output State
255
10,281
Full scale (RAB 1 LSB + 2 × RW)
128
5380
Midscale
1
359
1 LSB + 2 × RW
0
320
Zero scale (wiper contact resistance)
Note that in the zero-scale condition, a finite wiper resistance of
320 Ω is present. Care should be taken to limit the current flow
between W and B in this state to a maximum pulse current of no
more than 20 mA. Otherwise, degradation or possible destruction
of the internal switch contact may occur.
Similar to the mechanical potentiometer, the resistance of the
RDAC between Wiper W and Terminal A also produces a
digitally controlled complementary resistance, RWA. When these
terminals are used, the B terminal can be opened. Setting the
resistance value for RWA starts at a maximum value of resistance
and decreases as the data loaded in the latch increases in value.
The general equation for this operation is
W
AB
WA
R
D
R
2
256
)
(
(2)
When RAB is 10 kΩ and the B terminal is open circuited, the
output resistance, RWA, is set according to the RDAC latch
codes, as listed in Table 8.
Table 8. Codes and Corresponding RWA Resistance
D (Dec)
RWA (Ω)
Output State
255
359
Full scale
128
5320
Midscale
1
10,280
1 LSB + 2 × RW
0
10,320
Zero scale
Typical device-to-device matching is process-lot dependent and
may vary by up to ±30%. Because the resistance element is pro-
cessed in thin-film technology, the change in RAB with temperature
has a very low temperature coefficient of 35 ppm/°C.
相关PDF资料 |
PDF描述 |
|---|---|
| AD5162BRMZ10 | IC POT DUAL 10K 256POS 10-MSOP |
| AD5248BRMZ10 | IC DGTL POT DUAL 10K I2C 10-MSOP |
| DS4000D0N/WBGA | IC OSC TCXO 13MHZ 24-BGA |
| DS4000A0N/WBGA | IC OSC TCXO 10MHZ 24BGA |
| VE-BND-IU-F4 | CONVERTER MOD DC/DC 85V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5248BRMZ50-RL7 | 功能描述:IC DGTL POT 256POS 50K DL 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,300 系列:WiperLock™ 接片:257 电阻（欧姆）:100k 电路数:1 温度系数:标准值 150 ppm/°C 存储器类型:易失 接口:3 线 SPI（芯片选择） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VDFN 裸露焊盘 供应商设备封装:8-DFN-EP（3x3） 包装:带卷 (TR) |
| AD5248EVAL | 功能描述:BOARD EVAL FOR AD5248 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| AD524A | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Instrumentation Amplifier |
| AD524AD | 功能描述:IC AMP INST 1MHZ PREC LN 16CDIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:Excalibur™ 放大器类型:J-FET 电路数:1 输出类型:- 转换速率:45 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:20pA 电压 - 输入偏移:490µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
| AD524AD/+ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Instrumentation Amp， Pin-Programmable |
发布紧急采购，3分钟左右您将得到回复。