参数资料
| 型号： | AD5253BRU1-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/32页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT QUAD 1K 20-TSSOP |
| 标准包装： | 1,000 |
| 接片： | 64 |
| 电阻（欧姆）： | 1k |
| 电路数： | 4 |
| 温度系数： | 标准值 650 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.7 V ~ 5.5 V，±2.25 V ~ 2.75 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD5253/AD5254
Data Sheet
Rev. C | Page 18 of 32
RDAC/EEMEM Quick Commands
The AD5253/AD5254 feature 12 quick commands that facilitate
easy manipulation of RDAC wiper settings and provide RDAC-
to-EEMEM storing and restoring functions. The command
format is shown in Figure 31, and the command descriptions
are shown in Table 9.
When using a quick command, issuing a third byte is not
needed, but is allowed. The quick commands reset and store
RDAC to EEMEM require acknowledge polling to determine
whether the command has finished executing.
RAB Tolerance Stored in Read-Only Memory
The AD5253/AD5254 feature patented RAB tolerances storage in
the nonvolatile memory. The tolerance of each channel is stored
in the memory during the factory production and can be read
by users at any time. The knowledge of the stored tolerance,
users to predict RAB accurately. This feature is valuable for
precision, rheostat mode, and open-loop applications, in which
knowledge of absolute resistance is critical.
The stored tolerances reside in the read-only memory and are
expressed as percentages. Each tolerance is 16 bits long and is
stored in two memory locations (see Table 10). The tolerance
data is expressed in sign magnitude binary format stored in two
bytes; an example is shown in Figure 32 . For the first byte in
Register N, the MSB is designated for the sign (0 = + and 1 = –)
and the 7 LSB is designated for the integer portion of the
tolerance. For the second byte in Register N + 1, all eight data
bits are designated for the decimal portion of tolerance. As
10 k and the data readback from Address 11000 shows 0001
1100 and Address 11001 shows 0000 1111, then RDAC0
tolerance can be calculated as
MSB: 0 = +
Next 7 MSB: 001 1100 = 28
8 LSB: 0000 1111 = 15 × 2–8 = 0.06
Tolerance = 28.06% and, therefore,
RAB_ACTUAL = 12.806 k
EEMEM Write-Acknowledge Polling
After each write operation to the EEMEM registers, an internal
write cycle begins. The I2C interface of the device is disabled. To
determine if the internal write cycle is complete and the I2C
interface is enabled, interface polling can be executed. I2C
interface polling can be conducted by sending a start condition
followed by the slave address and the write bit. If the I2C
interface responds with an ACK, the write cycle is complete and
the interface is ready to proceed with further operations. Other-
wise, I2C interface polling can be repeated until it succeeds.
Command 2 and Command 7 also require acknowledge polling.
EEMEM Write Protection
Setting the WP pin to logic low after EEMEM programming
protects the memory and RDAC registers from future write
operations. In this mode, the EEMEM and RDAC read
operations function as normal.
Table 9. RDAC-to-EEMEM Interface and RDAC Operation Quick Command Bits (CMD/REG = 1, A2 = 0)
C3
C2
C1
C0
Command Description
0
NOP
0
1
Restore EEMEM (A1, A0) to RDAC (A1, A0)1
0
1
0
Store RDAC (A1, A0) to EEMEM (A1, A0)
0
1
Decrement RDAC (A1, A0) 6 dB
0
1
0
Decrement all RDACs 6 dB
0
1
0
1
Decrement RDAC (A1, A0) one step
0
1
0
Decrement all RDACs one step
0
1
Reset: restore EEMEMs to all RDACs
1
0
Increment RDACs (A1, A0) 6 dB
1
0
1
Increment all RDACs 6 dB
1
0
1
0
Increment RDACs (A1, A0) one step
1
0
1
Increment all RDACs one step
1
0
Reserved
:
1
Reserved
1 This command leaves the device in the EEMEM read power state, which consumes power. Issue the NOP command to return the device to its idle state.
相关PDF资料 |
PDF描述 |
|---|---|
| MS3106A36-7P | CONN PLUG 47POS STRAIGHT W/PINS |
| MS27497T20B2PB | CONN RCPT 65POS WALL MNT W/PINS |
| AD5253BRU10-RL7 | IC DGTL POT QUAD 10K 20-TSSOP |
| MS3124F12-10P | CONN RCPT 10POS JAM NUT W/PINS |
| M83723/85W2016N | CONN RCPT 16POS JAM NUT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5253BRU50 | 功能描述:IC DGTL POT QUAD 50K 20-TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD5253BRU50-RL7 | 功能描述:IC DGTL POT QUAD 50K 20-TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD5253BRUZ1 | 功能描述:IC POT DGTL QUAD 1K I2C 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD5253BRUZ10 | 功能描述:IC DGTL POT 64P 10K QUAD 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,300 系列:WiperLock™ 接片:257 电阻（欧姆）:100k 电路数:1 温度系数:标准值 150 ppm/°C 存储器类型:易失 接口:3 线 SPI（芯片选择） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VDFN 裸露焊盘 供应商设备封装:8-DFN-EP（3x3） 包装:带卷 (TR) |
| AD5253BRUZ100 | 功能描述:IC POT DGTL QUAD 100K 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。