参数资料
| 型号： | AD5259BRMZ5 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL 5K 256POS 10-MSOP |
| 标准包装： | 50 |
| 接片： | 256 |
| 电阻（欧姆）： | 5k |
| 电路数： | 1 |
| 温度系数： | 标准值 500 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.7 V ~ 3.3 V，4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 管件 |
| 产品目录页面： | 787 (CN2011-ZH PDF) |
| 配用： | AD5259EVAL-ND - BOARD EVAL FOR AD5259 DGTL POT |
AD5259
Data Sheet
Rev. C | Page 14 of 24
THEORY OF OPERATION
The AD5259 is a 256-position digitally-controlled variable
resistor (VR) device. EEPROM is pre-loaded at midscale from
the factory, and initial power-up is, accordingly, at midscale.
PROGRAMMING THE VARIABLE RESISTOR
Rheostat Operation
The nominal resistance (RAB) of the RDAC between Terminal A
and Terminal B is available in 5 k, 10 k, 50 k, and 100 k.
The nominal resistance of the VR has 256 contact points accessed
by the wiper terminal. The 8-bit data in the RDAC latch is
decoded to select one of 256 possible settings.
A
W
B
A
W
B
A
W
B
05026-036
Figure 38. Rheostat Mode Configuration
The general equation determining the digitally programmed
output resistance between Wiper W and Terminal B is
W
AB
WB
R
D
R
×
+
×
=
2
256
)
(
(1)
where:
D is the decimal equivalent of the binary code loaded in the
8-bit RDAC register.
RAB is the end-to-end resistance.
RW is the wiper resistance contributed by the ON resistance of
each internal switch.
D5
D4
D3
D7
D6
D2
D1
D0
RDAC
LATCH
AND
DECODER
RS
A
W
B
05026-037
Figure 39. AD5259 Equivalent RDAC Circuit
In the zero-scale condition, there is a relatively low value finite
wiper resistance. Care should be taken to limit the current flow
between Wiper W and Terminal B in this state to a maximum
pulse current of no more than 20 mA. Otherwise, degradation
or destruction of the internal switch contact can occur.
Similar to the mechanical potentiometer, the resistance of the
RDAC between Wiper W and Terminal A produces a digitally
controlled complementary resistance, RWA. The resistance value
setting for RWA starts at a maximum value of resistance and
decreases as the data loaded in the latch increases in value.
The general equation for this operation is
W
AB
WA
R
D
R
×
+
×
=
2
256
)
(
(2)
Typical device-to-device matching is process lot dependent and
may vary by up to ±30%. For this reason, resistance tolerance is
stored in the EEPROM, enabling the user to know the actual
RAB within 0.1%.
PROGRAMMING THE POTENTIOMETER DIVIDER
Voltage Output Operation
The digital potentiometer easily generates a voltage divider at
Wiper W to Terminal B and Wiper W to Terminal A propor-
tional to the input voltage at Terminal A to Terminal B. Unlike
the polarity of VDD to GND, which must be positive, voltage
across Terminal A to Terminal B, Wiper W to Terminal A, and
Wiper W to Terminal B can be at either polarity.
A
VI
W
B
VO
05026-038
Figure 40. Potentiometer Mode Configuration
If ignoring the effect of the wiper resistance for approximation,
connecting the A terminal to 5 V and the B terminal to ground
produces an output voltage at Wiper W to Terminal B starting
at 0 V up to 1 LSB less than 5 V. The general equation defining
the output voltage at VW with respect to ground for any valid
input voltage applied to Terminal A and Terminal B is
B
A
W
V
D
V
D
V
256
)
(
+
=
(3)
A more accurate calculation, which includes the effect of wiper
resistance, VW, is
B
AB
WA
A
AB
WB
W
V
R
D
R
V
R
D
R
D
V
)
(
)
(
)
(
+
=
(4)
Operation of the digital potentiometer in the divider mode
results in a more accurate operation over temperature. Unlike
the rheostat mode, the output voltage is dependent mainly
on the ratio of the Internal Resistors RWA and RWB and not
the absolute values.
相关PDF资料 |
PDF描述 |
|---|---|
| AD5220BRZ10 | IC POT DGTL 10K 128POS 8-SOIC |
| MCP7940M-I/ST | IC RTCC 64B I2C SRAM 8-TSSOP |
| AD5259BRMZ10 | IC DGTL POT 10K 256POS 10-MSOP |
| AD5200BRMZ10 | IC POT DGTL 10K 256POS 10MSOP |
| MCP79401T-I/MNY | IC CLK RTCC 64B EUI-48 8-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5259BRMZ50 | 功能描述:IC POT DGTL 50K 256POS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,300 系列:WiperLock™ 接片:257 电阻（欧姆）:100k 电路数:1 温度系数:标准值 150 ppm/°C 存储器类型:易失 接口:3 线 SPI（芯片选择） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VDFN 裸露焊盘 供应商设备封装:8-DFN-EP（3x3） 包装:带卷 (TR) |
| AD5259BRMZ50-R7 | 功能描述:IC POT DGTL 50K 256POS 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD5259BRMZ5-R7 | 功能描述:IC POT DGTL 5K 256POS 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD5259EVAL | 功能描述:BOARD EVAL FOR AD5259 DGTL POT RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| AD5259EVAL2 | 制造商:AD 制造商全称:Analog Devices 功能描述:Nonvolatile, I2C-Compatible 256-Position, Digital Potentiometer |
发布紧急采购，3分钟左右您将得到回复。