参数资料
| 型号： | AD5263BRUZ20 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT QUAD 20K 24-TSSOP |
| 标准包装： | 62 |
| 接片： | 256 |
| 电阻（欧姆）： | 20k |
| 电路数： | 4 |
| 温度系数： | 标准值 30 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | I²C，SPI（芯片选择，设备位址） |
| 电源电压： | 2.7 V ~ 5.5 V，5 V ~ 15 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 787 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
AD5263
Rev. F | Page 23 of 28
APPLICATIONS INFORMATION
BIPOLAR DC OR AC OPERATION FROM DUAL
SUPPLIES
The AD5263 can be operated from dual supplies, enabling
control of ground referenced ac signals or bipolar operation.
The ac signal, as high as VDD/VSS, can be applied directly across
Terminal A to Terminal B, with the output taken from Terminal W.
03142-
056
GND
SCLK
VDD
AD5263
C
GND
MCSI
SDA
SCL
VDD
VSS
+5.0V
±5V p-p
±2.5V p-p
_
5.0V
D = 0x90
A1
W1
B1
A2
W2
B2
Figure 57. Bipolar Operation from Dual Supplies
GAIN CONTROL COMPENSATION
A digital potentiometer is commonly used in gain control such
as the noninverting gain amplifier shown in Figure 58.
R1
47k
25pF
C1
VI
B
A
R2
VO
U1
W
200k
C2
4.7pF
03142-
057
Figure 58. Typical Noninverting Gain Amplifier
Notice the RDAC B terminal parasitic capacitance is connected to
the op amp noninverting node. It introduces a zero for the 1/βo
term with +20 dB/dec, whereas a typical op amp GBP has
20 dB/dec characteristics. A large R2 and finite C1 can cause
this zero’s frequency to fall well below the crossover frequency.
Thus, the rate of closure becomes 40 dB/dec and the system has
0° phase margin at the crossover frequency. The output may ring or
oscillate if the input is a rectangular pulse or step function.
Similarly, it is also likely to ring when switching between two gain
values, because this is equivalent to a step change at the input.
Depending on the op amp GBP, reducing the feedback resistor
may extend the zero’s frequency far enough to overcome the
problem. A better approach is to include a compensation capacitor
C2 to cancel the effect caused by C1. Optimum compensation
occurs when R1 × C1 = R2 × C2. This is not an option, because
of the variation of R2. As a result, one may use the relationship
described and scale C2 as if R2 is at its maximum value. Doing
so may overcompensate and compromise the performance slightly
when R2 is set at low values. However, it avoids the gain peaking,
ringing, or oscillation in the worst case. For critical applications,
C2 should be found empirically to suit the need. In general, C2
in the range of a few pF to no more than a few tenths of pF is
usually adequate for the compensation.
Similarly, there are W and A terminal capacitances connected to
the output (not shown); fortunately, their effect at this node is less
significant and the compensation can be disregarded in most cases.
PROGRAMMABLE VOLTAGE REFERENCE
For voltage divider mode operation (Figure 59), it is common to
buffer the output of the digital potentiometer unless the load is
much larger than RWB. Not only does the buffer serve the purpose
of impedance conversion, but it also allows a heavier load to be
driven.
03142-
058
U1
VIN
W
B
A
GND
VO
AD8601
1
A1
5V
VOUT
3
5V
AD5263
AD1582
Figure 59. Programmable Voltage Reference
相关PDF资料 |
PDF描述 |
|---|---|
| AD5233BRUZ50 | IC POT QUAD 50K 64POS 24-TSSOP |
| VE-23Z-MX-F2 | CONVERTER MOD DC/DC 2V 30W |
| VI-B6X-IU-F4 | CONVERTER MOD DC/DC 5.2V 200W |
| VE-23Z-MX-F1 | CONVERTER MOD DC/DC 2V 30W |
| MCP79411-I/MS | IC RTCC I2C SER EUI-48 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5263BRUZ20 | 制造商:Analog Devices 功能描述:DIG POT, QUAD, 256, 15V, 20KOHM, 24TSSOP; End To End Resistance:20kohm; Track Taper:Linear; Resistance Tolerance: 30%; Supply Voltage Min:4.5V; Supply Voltage Max:16.5V; Potentiometer IC Case Style:TSSOP; No. of Pins:24; No. of ;RoHS Compliant: Yes |
| AD5263BRUZ200 | 功能描述:IC POT QUAD 200K 256POS 24-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5263BRUZ200-R7 | 制造商:Analog Devices 功能描述:QUAD, 15 V, 256-POSITION DIGITAL POTENTIOMETER WITH PIN-SELE - Tape and Reel |
| AD5263BRUZ20-REEL7 | 功能描述:IC DGTL POT QUAD 20K 24-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5263BRUZ50 | 功能描述:IC POT QUAD 50K 256POS 24-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
发布紧急采购，3分钟左右您将得到回复。