- 您现在的位置：买卖IC网 > PDF目录373878 > AD5381BST-3-REEL (ANALOG DEVICES INC) CONNECTOR ACCESSORY PDF资料下载
参数资料
| 型号： | AD5381BST-3-REEL |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | DAC |
| 英文描述： | CONNECTOR ACCESSORY |
| 中文描述： | PARALLEL, WORD INPUT LOADING, 6 us SETTLING TIME, 12-BIT DAC, PQFP100 |
| 封装： | 14 X 14 MM, MS-026-BED, LQFP-100 |
| 文件页数： | 28/36页 |
| 文件大小： | 1200K |
| 代理商： | AD5381BST-3-REEL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页
AD5381
I
2
C SERIAL INTERFACE
The AD5381 features an I
2
C compatible 2-wire interface
consisting of a serial data line (SDA) and a serial clock line
(SCL). SDA and SCL facilitate communication between the
AD5381 and the master at rates up to 400 kHz. Figure 6 shows
the 2-wire interface timing diagrams that incorporate three
different modes of operation. In selecting the I
2
C operating
mode, first configure serial operating mode (SER/PAR = 1) and
then select I
2
C mode by configuring the SPI/I2C pin to a Logic
1. The device is connected to the I
2
C bus as a slave device (i.e.,
no clock is generated by the AD5381). The AD5381 has a 7-bit
slave address 1010 1(AD1)(AD0). The 5 MSB are hard-coded
and the 2 LSB are determined by the state of the AD1 and AD0
pins. The facility to hardware configure AD1 and AD0 allows
four of these devices to be configured on the bus.
I
2
C Data Transfer
One data bit is transferred during each SCL clock cycle. The
data on SDA must remain stable during the high period of the
SCL clock pulse. Changes in SDA while SCL is high are control
signals that configure START and STOP conditions. Both SDA
and SCL are pulled high by the external pull-up resistors when
the I
2
C bus is not busy.
START and STOP Conditions
A master device initiates communication by issuing a START
condition. A START condition is a high-to-low transition on
SDA with SCL high. A STOP condition is a low-to-high
transition on SDA while SCL is high. A START condition from
the master signals the beginning of a transmission to the
AD5381. The STOP condition frees the bus. If a repeated
START condition (Sr) is generated instead of a STOP condition,
the bus remains active.
Repeated START Conditions
A repeated START (Sr) condition may indicate a change of data
direction on the bus. Sr may be used when the bus master is
writing to several I
2
C devices and wants to maintain control of
the bus.
Acknowledge Bit (ACK)
The acknowledge bit (ACK) is the ninth bit attached to any
8-bit data-word. ACK is always generated by the receiving
device. The AD5381 devices generate an ACK when receiving
an address or data by pulling SDA low during the ninth clock
period. Monitoring ACK allows for detection of unsuccessful
data transfers. An unsuccessful data transfer occurs if a
receiving device is busy or if a system fault has occurred. In the
event of an unsuccessful data transfer, the bus master should
reattempt communication.
Rev. A | Page 28 of 36
AD5381 Slave Addresses
A bus master initiates communication with a slave device by
issuing a START condition followed by the 7-bit slave address.
When idle, the AD5381 waits for a START condition followed
by its slave address. The LSB of the address word is the Read/
Write (R/W) bit. The AD5381 is a receive only device; when
communicating with the AD5381, R/W = 0. After receiving the
proper address 1010 1(AD1)(AD0), the AD5381 issues an ACK
by pulling SDA low for one clock cycle.
The AD5381 has four different user programmable addresses
determined by the AD1 and AD0 bits.
Write Operation
There are three specific modes in which data can be written to
the AD5381 DAC.
4-Byte Mode
When writing to the AD5381 DACs, the user must begin with
an address byte (R/W = 0) after which the DAC acknowledges
that it is prepared to receive data by pulling SDA low. The
address byte is followed by the pointer byte; this addresses the
specific channel in the DAC to be addressed and is also
acknowledged by the DAC. Two bytes of data are then written
to the DAC, as shown in Figure 31. A STOP condition follows.
This allows the user to update a single channel within the
AD5381 at any time and requires four bytes of data to be
transferred from the master.
3-Byte Mode
In 3-byte mode, the user can update more than one channel in a
write sequence without having to write the device address byte
each time. The device address byte is only required once; sub-
sequent channel updates require the pointer byte and the data
bytes. In 3-byte mode, the user begins with an address byte
(R/W = 0), after which the DAC will acknowledge that it is
prepared to receive data by pulling SDA low. The address byte is
followed by the pointer byte. This addresses the specific channel
in the DAC to be addressed and is also acknowledged by the
DAC. This is then followed by the two data bytes. REG1 and
REG0 determine the register to be updated.
If a STOP condition does not follow the data bytes, another
channel can be updated by sending a new pointer byte followed
by the data bytes. This mode only requires three bytes to be sent
to update any channel once the device has been initially
addressed, and reduces the software overhead in updating the
AD5381 channels. A STOP condition at any time exits this
mode. Figure 32 shows a typical configuration.
相关PDF资料 |
PDF描述 |
|---|---|
| AD5381BST-5 | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
| AD5381BST-5-REEL | 40-Channel, 3 V/5 V, Single-Supply, 12-Bit, Voltage Output DAC |
| AD5382BST-3-REEL | CONNECTOR ACCESSORY |
| AD5382 | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
| AD5382BST-3 | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5381BST-5 | 制造商:Analog Devices 功能描述:DAC 40-CH Resistor-String 12-bit 100-Pin LQFP |
| AD5381BST-5-REEL | 制造商:Analog Devices 功能描述:DAC 40-CH Resistor-String 12-bit 100-Pin LQFP T/R |
| AD5381BSTZ-3 | 功能描述:IC DAC 12BIT 40CHAN 3V 100LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:1 系列:- 设置时间:4.5µs 位数:12 数据接口:串行，SPI? 转换器数目:1 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOICN 包装:剪切带 (CT) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:* 其它名称:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD5381BSTZ-3-REEL | 功能描述:IC DAC 12BIT 40CH 3V 100-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD5381BSTZ-5 | 功能描述:IC DAC 12BIT 40CH 5V 100-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
发布紧急采购，3分钟左右您将得到回复。