- 您现在的位置：买卖IC网 > PDF目录373878 > AD5384BBC-5 (ANALOG DEVICES INC) 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC PDF资料下载
参数资料
| 型号： | AD5384BBC-5 |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | DAC |
| 英文描述： | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
| 中文描述： | SERIAL INPUT LOADING, 8 us SETTLING TIME, 14-BIT DAC, PBGA100 |
| 封装： | 10 X 10 MM, MO-205AC, CSPBGA-100 |
| 文件页数： | 26/40页 |
| 文件大小： | 616K |
| 代理商： | AD5384BBC-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
AD5382
AD5382 INTERFACES
The AD5382 contains both parallel and serial interfaces.
Furthermore, the serial interface can be programmed to be
either SPI, DSP, MICROWIRE, or I
2
C compatible. The SER/PAR
pin selects parallel and serial interface modes. In serial mode,
the SPI/I2C pin is used to select DSP, SPI, MICROWIRE, or I
2
C
interface mode.
Rev. 0 | Page 26 of 40
The devices use an internal FIFO memory to allow high speed
successive writes in parallel interface mode. The user can con-
tinue writing new data to the device while write instructions are
being executed. The BUSY signal indicates the current status of
the device, going low while instructions in the FIFO are being
executed. In parallel mode, up to 128 successive instructions can
be written to the FIFO at maximum speed. When the FIFO is
full, any further writes to the device are ignored.
To minimize both the power consumption of the device and the
on-chip digital noise, the active interface only powers up fully
when the device is being written to, i.e., on the falling edge of
WR or the falling edge of SYNC.
DSP, SPI, MICROWIRE COMPATIBLE SERIAL
INTERFACES
The serial interface can be operated with a minimum of three
wires in standalone mode or four wires in daisy-chain mode.
Daisy chaining allows many devices to be cascaded together to
increase system channel count. The SER/PAR pin must be tied
high and the SPI/I2C pin (Pin 97) should be tied low to enable
the DSP/SPI/MICROWIRE compatible serial interface. In serial
interface mode, the user does not need to drive the parallel
input data pins. The serial interface’s control pins are
SYNC, DIN, SCLK
—Standard 3-Wire Interface Pins.
DCEN
—Selects Standalone Mode or Daisy-Chain Mode.
SDO
—Data Out Pin for Daisy-Chain Mode.
Figure 3 and Figure 5 show timing diagrams for a serial write to
the AD5382 in standalone and daisy-chain modes. The 24-bit
data-word format for the serial interface is shown in Table 19
A/B
. When toggle mode is enabled, this pin selects whether the
data write is to the A or B register. With toggle disabled, this bit
should be set to zero to select the A data register.
R/W
is the read or write control bit.
A4–A0
are used to address the input channels.
REG1 and REG0
select the register to which data is written, as
shown in Table 11.
DB13–DB0
contain the input data-word.
X
is a don’t care condition.
Standalone Mode
By connecting the DCEN (Daisy-Chain Enable) pin low, stand-
alone mode is enabled. The serial interface works with both a
continuous and a noncontinuous serial clock. The first falling
edge of SYNC starts the write cycle and resets a counter that
counts the number of serial clocks to ensure that the correct
number of bits are shifted into the serial shift register. Any
further edges on SYNC except for a falling edge are ignored
until 24 bits are clocked in. Once 24 bits have been shifted in,
the SCLK is ignored. In order for another serial transfer to take
place, the counter must be reset by the falling edge of SYNC.
Table 19. 32-Channel, 14-Bit DAC Serial Input Register Configuration
MSB
A/B
R/W
0
A4
A3
A2
A1
A0
REG1
REG0
DB13
DB12
DB11
DB10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
LSB
DB0
相关PDF资料 |
PDF描述 |
|---|---|
| AD5390BCP-3-REEL | 8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs |
| AD5391BCP-3-REEL | 8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs |
| AD5391BST-3 | 8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs |
| AD5391BST-5 | 8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs |
| AD5391BST-5-REEL | 8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5384BBC-5REEL7 | 功能描述:IC DAC 14BIT 40CH 5V 100-CSPBGA RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
| AD5384BBCZ-3 | 功能描述:IC DAC 14BIT 40CH 5V 100-CSPBGA RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
| AD5384BBCZ-5 | 功能描述:IC DAC 14BIT 40CH 5V 100-CSPBGA RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
| AD5384BBCZ-5REEL7 | 功能描述:14 Bit Digital to Analog Converter 40 100-CSBGA (10x10) 制造商:analog devices inc. 系列:denseDAC 包装:带卷（TR） 零件状态:有效 位数:14 数模转换器数:40 建立时间:8μs 输出类型:Voltage - Buffered 差分输出:无 数据接口:I2C，SPI，DSP 参考类型:外部， 内部 电压 - 电源，模拟:5V 电压 - 电源，数字:2.7 V ~ 5.5 V INL/DNL（LSB）:±4（最大），-1/+2（最大） 架构:电阻串 DAC 工作温度:-40°C ~ 85°C 封装/外壳:100-LFBGA，CSPBGA 供应商器件封装:100-CSBGA（10x10） 标准包装:400 |
| AD538AD | 功能描述:IC MULT/DIV REALTIME ACU 18-CDIP RoHS:否 类别:集成电路 (IC) >> 线性 - 模拟乘法器，除法器 系列:- 标准包装:25 系列:HA 功能:模拟乘法器 位元/级数:四象限 封装/外壳:16-CDIP（0.300"，7.62mm） 供应商设备封装:16-CDIP 侧面铜焊 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。