参数资料
型号: AD5439YRUZ-REEL7
厂商: Analog Devices Inc
文件页数: 10/29页
文件大小: 0K
描述: IC DAC DUAL 10BIT MULT 16TSSOP
产品培训模块: Data Converter Fundamentals
DAC Architectures
标准包装: 1,000
设置时间: 35ns
位数: 10
数据接口: 串行
转换器数目: 2
电压电源: 单电源
功率耗散(最大): 3.5µW
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 16-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 16-TSSOP
包装: 带卷 (TR)
输出数目和类型: 4 电流,单极;4 电流,双极
采样率(每秒): 2.47M
其它名称: AD5439YRUZ-REEL7TR
Data Sheet
AD5429/AD5439/AD5449
Rev. E | Page 17 of 28
SINGLE-SUPPLY APPLICATIONS
Voltage-Switching Mode
Figure 40 shows the DACs operating in voltage-switching mode.
The reference voltage, VIN, is applied to the IOUT1A pin; IOUT2A
is connected to AGND; and the output voltage is available at the
VREFA terminal. In this configuration, a positive reference voltage
results in a positive output voltage, making single-supply operation
possible. The output from the DAC is voltage at a constant
impedance (the DAC ladder resistance). Therefore, an op amp
is necessary to buffer the output voltage. The reference input
no longer sees a constant input impedance; instead, it sees one
that varies with code. Therefore, the voltage input should be
driven from a low impedance source.
Note that VIN is limited to low voltages because the switches
in the DAC ladder no longer have the same source-drain drive
voltage. As a result, their on resistance differs and degrades the
integral linearity of the DAC. Also, VIN must not go negative by
more than 0.3 V, or an internal diode turns on, causing the device
to exceed the maximum ratings. In this type of application, the
full range of multiplying capability of the DAC is lost.
Positive Output Voltage
The output voltage polarity is opposite to the VREF polarity for
dc reference voltages. To achieve a positive voltage output, an
applied negative reference to the input of the DAC is preferred
over the output inversion through an inverting amplifier because
of the resistor tolerance errors. To generate a negative reference,
the reference can be level-shifted by an op amp such that the VOUT
and GND pins of the reference become the virtual ground and
2.5 V, respectively, as shown in Figure 41.
VOUT
VDD
GND
VIN
IOUT2A
IOUT1A
RFBA VDD
VREFA
R2
R1
04464-
009
NOTES
1. ADDITIONAL PINS OMITTED FOR CLARITY.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
IF A1 IS A HIGH SPEED AMPLIFIER.
8-/10-/12-BIT
DAC
Figure 40. Single-Supply Voltage-Switching Mode
VOUT = 0V TO +2.5V
VDD = +5V
GND
IOUT2A
IOUT1A
RFBA
VDD
VREFA
C1
GND
VIN
VOUT
ADR03
+5V
–5V
8-/10-/12-BIT
DAC
–2.5V
04464-010
NOTES
1. ADDITIONAL PINS OMITTED FOR CLARITY.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
IF A1 IS A HIGH SPEED AMPLIFIER.
Figure 41. Positive Voltage Output with Minimum Components
相关PDF资料
PDF描述
SI5330G-A00218-GM IC CLK BUFFER TRANSLA 1:8 24-QFN
SI5330G-A00217-GM IC CLK BUFFER TRANSLA 1:8 24-QFN
VE-263-MW-F4 CONVERTER MOD DC/DC 24V 100W
SI5330F-A00216-GM IC CLK BUFFER TRANSLA 1:8 24-QFN
SI5330F-A00215-GM IC CLK BUFFER TRANSLA 1:8 24-QFN
相关代理商/技术参数
参数描述
AD544 制造商:AD 制造商全称:Analog Devices 功能描述:High Performance, BiFET Operational Amplifiers
AD5440 制造商:AD 制造商全称:Analog Devices 功能描述:Dual 8-,10-,12-Bit High Bandwidth Multiplying DACs with Serial Interface
AD5440YRU 功能描述:IC DAC 10BIT DUAL MULT 24-TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散(最大):55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP(0.209",5.30mm 宽) 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流,单极;1 电流,双极 采样率(每秒):*
AD5440YRU-REEL 功能描述:IC DAC 10BIT MULTIPLYING 24TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?,串行,SPI? 转换器数目:8 电压电源:单电源 功率耗散(最大):2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-DFN-EP(4x3) 包装:管件 输出数目和类型:8 电压,单极 采样率(每秒):*
AD5440YRU-REEL7 功能描述:IC DAC 10BIT MULTIPLYING 24TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?,串行,SPI? 转换器数目:8 电压电源:单电源 功率耗散(最大):2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-DFN-EP(4x3) 包装:管件 输出数目和类型:8 电压,单极 采样率(每秒):*