参数资料
| 型号： | AD548KNZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 12/12页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP 1MHZ LP PREC 8DIP |
| 标准包装： | 50 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 转换速率： | 1.8 V/µs |
| 增益带宽积： | 1MHz |
| 电流 - 输入偏压： | 30pA |
| 电压 - 输入偏移： | 300µV |
| 电流 - 电源： | 170µA |
| 电流 - 输出 / 通道： | 15mA |
| 电压 - 电源，单路/双路(±)： | ±4.5 V ~ 18 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 产品目录页面： | 773 (CN2011-ZH PDF) |
Figure 9. Low Power Instrumentation Amplifier
Gains of 1 to 100 can be accommodated with gain nonlinearities
of less than 0.01%. Input errors, which contribute an output
error proportional to in amp gain, include a maximum untrimmed
input offset voltage of 0.5 mV and an input offset voltage drift
over temperature of 4
V/°C. Output errors, which are indepen-
dent of gain, will contribute an additional 0.5 mV offset and
4
V/°C drift. The maximum input current is 15 pA over the
common-mode range, with a common-mode impedance of over
1
× 1012 . Resistor pairs R3/R5 and R4/R6 should be ratio
matched to 0.01% to take full advantage of the AD548’s high
common-mode rejection. Capacitors C1 and C1
′ compensate for
peaking in the gain over frequency caused by input capacitance
when gains of 1 to 3 are used.
The –3 dB small signal bandwidth for this low power instrumenta-
tion amplifier is 700 kHz for a gain of 1 and 10 kHz for a gain of
100. The typical output slew rate is 1.8 V/
s.
LOG RATIO AMPLIFIER
Log ratio amplifiers are useful for a variety of signal conditioning
applications, such as linearizing exponential transducer outputs
and compressing analog signals having a wide dynamic range.
The AD548’s picoamp level input current and low input offset
voltage make it a good choice for the front-end amplifier of the
log ratio circuit shown in Figure 10. This circuit produces an
output voltage equal to the log base 10 of the ratio of the input
currents I1 and I2. Resistive inputs R1 and R2 are provided for
voltage inputs.
Input currents I1 and I2 set the collector currents of Q1 and Q2,
a matched pair of logging transistors. Voltages at points A and
B are developed according to the following familiar diode
equation:
V
BE = (kT /q )ln ( IC / I ES )
In this equation, k is Boltzmann’s constant, T is absolute tem-
perature, q is an electron charge, and IES is the reverse saturation
current of the logging transistors. The difference of these two
voltages is taken by the subtractor section and scaled by a factor
of approximately 16 by resistors R9, R10, and R8. Temperature
Application Hints–AD548
PHOTODIODE PREAMP
The performance of the photodiode preamp shown in Figure 7
is enhanced by the AD548’s low input current, input voltage
offset, and offset voltage drift. The photodiode sources a current
proportional to the incident light power on its surface. RF converts
the photodiode current to an output voltage equal to RF
× IS.
Figure 7.
An error budget illustrating the importance of low amplifier
input current, voltage offset, and offset voltage drift to minimize
output voltage errors can be developed by considering the equi-
valent circuit for the small (0.2 mm
2 area) photodiode shown in
Figure 7. The input current results in an error proportional to
the feedback resistance used. The amplifier’s offset will produce
an error proportional to the preamp’s noise gain (I + RF/RSH),
where RSH is the photodiode shunt resistance. The amplifier’s
input current will double with every 10
°C rise in temperature,
and the photodiode’s shunt resistance halves with every 10
°C
rise. The error budget in Figure 8 assumes a room temperature
photodiode RSH of 500 M
, and the maximum input current
and input offset voltage specs of an AD548C.
TEMP
CRSH (M )VOS ( V) (1+ RF/RSH) VOS
IB (pA)
IBRF
TOTAL
–25
15,970
150
151
V0.30
30
V
181
V
0
2,830
200
207
V2.26
262
V 469 V
25
500
250
300
V
10.00
1.0 mV 1.30 mV
50
88.5
300
640
V
56.6
5.6 mV 6.24 mV
75
15.6
350
2.6 mV
320
32 mV
34.6 mV
85
7.8
370
5.1 mV
640
64 mV
69.1 mV
Figure 8. Photodiode Preamp Errors Over Temperature
The capacitance at the amplifier’s negative input (the sum of the
photodiode’s shunt capacitance, the op amp’s differential input
capacitance, stray capacitance due to wiring, etc.) will cause a
rise in the preamp’s noise gain over frequency. This can result in
excess noise over the bandwidth of interest. CF reduces the
noise gain “peaking” at the expense of bandwidth.
INSTRUMENTATION AMPLIFIER
The AD548C’s maximum input current of 10 pA makes it an
excellent building block for the high input impedance instru-
mentation amplifier shown in Figure 9. Total current drain for
this circuit is under 600
A. This configuration is optimal for
conditioning differential voltages from high impedance sources.
The overall gain of the circuit is controlled by RG, resulting in
the following transfer function:
V
OUT
V
IN
= 1 +
(R
1 + R2 )
R
G
REV. D
–9–
相关PDF资料 |
PDF描述 |
|---|---|
| 155244-2300-RB | CONN HEADER 2MM 44POS VERT SMT |
| M80-5403442 | CONN HDR 2MM R/A W/SCREW 34POS |
| PEC19SBBN | CONN HEADER .100 SINGL R/A 19POS |
| 155250-5302-RB | CONN HEADER 2MM 50POS R/A .112" |
| PBC11SFDN | CONN HEADER .100 SINGL STR 11POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD548KNZ | 制造商:Analog Devices 功能描述:Operational Amplifier (Op-Amp) IC 制造商:Analog Devices 功能描述:IC, OP-AMP, 1MHZ, 1.8V/ us, DIP-8 |
| AD548KR | 制造商:Rochester Electronics LLC 功能描述:LOW POWER BIFET OP AMP IC - Bulk |
| AD548KR-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision, Low Power BiFET Op Amp |
| AD548S | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision, Low Power BiFET Op Amp |
| AD548SH | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision, Low Power BiFET Op Amp |
发布紧急采购，3分钟左右您将得到回复。