- 您现在的位置：买卖IC网 > PDF目录2134 > AD5750-1ACPZ-REEL7 (Analog Devices Inc)IC CURR/VOLT OUT DVR 32LFCSP PDF资料下载
参数资料
| 型号： | AD5750-1ACPZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 22/36页 |
| 文件大小： | 0K |
| 描述： | IC CURR/VOLT OUT DVR 32LFCSP |
| 标准包装： | 1,500 |
| 放大器类型： | 仪表 |
| 电路数： | 1 |
| 转换速率： | 2 V/µs |
| 电流 - 电源： | 5.2mA |
| 电流 - 输出 / 通道： | 24mA |
| 电压 - 电源，单路/双路(±)： | ±10.8 V ~ 26.4 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-LFCSP |
| 供应商设备封装： | 32-LFCSP-VQ |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
AD5750/AD5750-1
Rev. C | Page 29 of 36
DETAILED DESCRIPTION OF FEATURES
OUTPUT FAULT ALERT—SOFTWARE MODE
In software mode, the AD5750/AD5750-1 are equipped with
one FAULT pin; this is an open-drain output allowing several
AD5750/AD5750-1 devices to be connected together to one
pull-up resistor for global fault detection. In software mode, the
FAULT pin is forced active low by any one of the following fault
scenarios:
The voltage at IOUT attempts to rise above the compliance
range due to an open-loop circuit or insufficient power
supply voltage. The internal circuitry that develops the
fault output avoids using a comparator with window limits
because this requires an actual output error before the fault
output becomes active. Instead, the signal is generated
when the internal amplifier in the output stage has less
than approximately 1 V of remaining drive capability.
Thus, the fault output activates slightly before the com-
pliance limit is reached. Because the comparison is made
within the feedback loop of the output amplifier, the output
accuracy is maintained by its open-loop gain, and an
output error does not occur before the fault output
becomes active.
A short is detected on the voltage output pin (VOUT). The
short-circuit current is limited to 15 mA.
An interface error is detected due to packet error checking
(PEC) failure. See the Packet Error Checking section.
If the core temperature of the AD5750/AD5750-1 exceeds
approximately 150°C.
OUTPUT FAULT ALERT—HARDWARE MODE
In hardware mode, the AD5750/AD5750-1 are equipped with
three fault pins: VFAULT, IFAULT, and TEMP. These are open-
drain outputs allowing several AD5750/AD5750-1 devices to
be connected together to one pull-up resistor for global fault
detection. In hardware control mode, these fault pins are forced
active by any one of the following fault scenarios:
An open circuit is detected. The voltage at IOUT attempts
to rise above the compliance range, due to an open-loop
circuit or insufficient power supply voltage. The internal
circuitry that develops the fault output avoids using a
comparator with window limits because this requires an
actual output error before the fault output becomes active.
Instead, the signal is generated when the internal amplifier
in the output stage has less than approximately 1 V of
remaining drive capability. Thus, the fault output activates
slightly before the compliance limit is reached. Because the
comparison is made within the feedback loop of the output
amplifier, the output accuracy is maintained by its open-
loop gain, and an output error does not occur before the
fault output becomes active. If this fault is detected, the
IFAULT pin is forced low.
A short is detected on the voltage output pin (VOUT). The
short-circuit current is limited to 15 mA. If this fault is
detected, the VFAULT pin is forced low.
The core temperature of the AD5750/AD5750-1 exceeds
approximately 150°C. If this fault is detected, the TEMP
pin is forced low.
VOLTAGE OUTPUT SHORT-CIRCUIT PROTECTION
Under normal operation, the voltage output sinks and sources
up to 12 mA and maintains specified operation. The maximum
current that the voltage output delivers is 15 mA; this is the
short-circuit current.
ASYNCHRONOUS CLEAR (CLEAR)
CLEAR is an active high clear that allows the voltage output
to be cleared to either zero-scale code or midscale code, and is
user-selectable via the CLRSEL pin or the CLRSEL bit of the input
shift register, as described in Table 8. (The clear select feature is
a logical OR function of the CLRSEL pin and the CLRSEL bit).
The current loop output clears to the bottom of its programmed
range. When the CLEAR signal is returned low, the output returns
to its programmed value or to a new programmed value. A clear
operation can also be performed via the clear command in the
control register.
Table 11. CLRSEL Options
CLRSEL
Output Clear Value
Unipolar Output
Voltage Range
Unipolar Current Output Range
Bipolar Output Range
Bipolar Current
Output Range
0
0 V
Zero scale; for example,
4 mA on the 4 mA to 20 mA range
0 mA on the 0 mA to 20 mA range
Negative full scale
Zero scale; for example,
24 mA on the ±24 mA range
1
Midscale
Midscale; for example,
12 mA on the 4 mA to 20 mA range
10 mA on the 0 mA to 20 mA range
0 V
Midscale; for example,
0 mA on the ±24 mA range
相关PDF资料 |
PDF描述 |
|---|---|
| AD5750-2BCPZ-RL7 | IC CURR/VOLT OUT DRVR 32LFCSP |
| AD5751ACPZ-REEL7 | IC I/V OUTPUT DRIVER 60V 32LFCSP |
| AD582SD | IC AMP SAMPLE HOLD 25MA 14CDIP |
| AD585SQ | IC AMP SAMPLE HOLD 50MA 14CDIP |
| AD602AR | IC AMP VGA DUAL LN 50MA 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5750-1BCPZ | 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| AD5750-1BCPZ-REEL | 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| AD5750-1BCPZ-REEL7 | 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| AD5750-2 | 制造商:AD 制造商全称:Analog Devices 功能描述:Industrial Current/Voltage Output Driver |
| AD5750-2BCPZ | 功能描述:IC CURR/VOLT OUT DRIVER 32LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
发布紧急采购，3分钟左右您将得到回复。