参数资料
| 型号： | AD5751BCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/32页 |
| 文件大小： | 0K |
| 描述： | IC CURR/VOLT OUT DVR 32LFCSP |
| 标准包装： | 1 |
| 放大器类型： | 仪表 |
| 电路数： | 1 |
| 转换速率： | 2 V/µs |
| 电流 - 电源： | 5.2mA |
| 电流 - 输出 / 通道： | 24mA |
| 电压 - 电源，单路/双路(±)： | 10.8 V ~ 55 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-VQ（5x5） |
| 包装： | 托盘 |
| 产品目录页面： | 771 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Data Sheet
AD5751
Rev. B | Page 23 of 32
CURRRENT OUTPUT ARCHITECTURE
The voltage input from the analog input VIN core (0 V to 4.096 V)
is either converted to a current (see Figure 52), which is then
mirrored to the supply rail so that the application simply sees
a current source output with respect to an internal reference
voltage, or it is buffered and scaled to output a software-selectable
unipolar voltage range (see Figure 53). The reference is used to
provide internal offsets for range and gain scaling. The selecta-
ble output range is programmable through the digital interface
(software mode) or via the range pins (R0 to R3) (hardware mode).
07269-
008
AVDD
VIN
VREF
A1
A2
R1
R3
R2
T1
T2
RANGE DECODE
FROM INTERFACE
VOUT RANGE
SCALING
IOUT
Figure 52. Current Output Configuration
07269-
009
VIN
(0V TO 4.096V)
VREF
VOUT SHORT FAULT
VOUT
VSENSE+
GND
RANGE DECODE
FROM INTERFACE
VOUT RANGE
SCALING
Figure 53. Voltage Output
DRIVING INDUCTIVE LOADS
When driving inductive or poorly defined loads, connect a 0.01 F
capacitor between IOUT and GND. This ensures stability with
loads beyond 50 mH. There is no maximum capacitance limit.
The capacitive component of the load may cause slower settling.
Voltage Output Amplifier
The voltage output amplifier is capable of driving a load of 1 k
(for 0 V to 5 V and 0 V to 10 V ranges) and a load of 5 k (for
0 V to 40 V range) and capacitive loads up to 2 F (with an
external compensation capacitor on the COMP1 and COMP2
pins). The source and sink capabilities of the output amplifier
can be seen in Figure 15. The slew rate is 2 V/s.
Internal to the device, there is a 2.5 M resistor connected
between VOUT and VSENSE+. If a fault condition occurs,
these resistors act to protect the AD5751 by ensuring that the
amplifier loop is closed so that the part does not enter into an
open-loop condition.
The current and voltage are output on separate pins and cannot
be output simultaneously. This allows the user to tie both the
current and voltage output pins together and configure the end
system as a single-channel output.
Driving Large Capacitive Loads
The voltage output amplifier is capable of driving capacitive loads
of up to 1 F with the addition of a nonpolarized compensation
capacitor between the COMP1 and COMP2 pins.
Without the compensation capacitor, up to 20 nF capacitive loads
can be driven. Care should be taken to choose an appropriate
value for the CCOMP capacitor. This capacitor, while allowing the
AD5751 to drive higher capacitive loads and reduce overshoot,
increases the settling time of the part and therefore affects the
bandwidth of the system. Considered values of this capacitor
should be in the range of 0 nF to 4 nF depending on the trade-off
required between settling time, overshoot, and bandwidth.
POWER-ON STATE OF THE AD5751
On power-up, the AD5751 senses whether hardware or software
mode is loaded and sets the power-up conditions accordingly.
In software SPI mode, the power-up state of the output is
dependent on the state of the CLEAR pin. If the CLEAR pin is
pulled high, the part powers up, driving an active 0 V on the
output. If the CLEAR pin is pulled low, the part powers up with
the voltage output channel in tristate mode. In both cases, the
current output channel powers up in the tristate condition (0
mA). This allows the voltage and current outputs to be
connected together if desired.
To put the part into normal operation, the user must set the
OUTEN bit in the control register to enable the output and, in
the same write, set the output range configuration using the R3
to R0 range bits. If the CLEAR pin is still high (active) during
this write, the part automatically clears to its normal clear state
as defined by the programmed range and by the CLRSEL pin or
the CLRSEL bit (see the Asynchronous Clear (CLEAR) section
for more details). The CLEAR pin must be taken low to operate
the part in normal mode.
The CLEAR pin is typically driven directly from a microcontroller.
In cases where the power supply for the AD5751 supply is
independent of the microcontroller power supply, the user can
connect a weak pull-up resistor to DVCC or a pull-down resistor
to ground to ensure that the correct power-up condition is
achieved independent of the microcontroller. A 10 k pull-up/
pull-down resistor on the CLEAR pin should be sufficient for
most applications.
If hardware mode is selected, the part powers up to the conditions
defined by the R3 to R0 range bits and the status of the OUTEN
or CLEAR pin. It is recommended to keep the output disabled
when powering up the part in hardware mode.
相关PDF资料 |
PDF描述 |
|---|---|
| RMCF0603JT4K70 | RES 4.7K OHM 1/10W 5% 0603 SMD |
| AD9631ARZ | IC OPAMP VF ULDIST 70MA 8SOIC |
| AD8228BRMZ-R7 | IC AMP INST PREC LDRIFT LN 8MSOP |
| RMCF0603JT1K00 | RES 1K OHM 1/10W 5% 0603 SMD |
| AD843KNZ | IC OPAMP GP 34MHZ 50MA 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5751BCPZ-REEL7 | 功能描述:IC I/V OUTPUT DRIVER 60V 32LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:150 系列:- 放大器类型:音频 电路数:2 输出类型:- 转换速率:5 V/µs 增益带宽积:12MHz -3db带宽:- 电流 - 输入偏压:100nA 电压 - 输入偏移:500µV 电流 - 电源:6mA 电流 - 输出 / 通道:50mA 电压 - 电源，单路/双路(±):4 V ~ 32 V，±2 V ~ 16 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| AD5752 | 制造商:AD 制造商全称:Analog Devices 功能描述:Complete, Dual, 12-/14-/16-Bit, Serial Input, Unipolar/Bipolar, Voltage Output DACs |
| AD5752AREZ | 功能描述:IC DAC DUAL 16BIT SERIAL 24TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| AD5752AREZ-REEL7 | 功能描述:IC DAC DUAL 16BIT SERIAL 24TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
| AD5752BREZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Complete, Dual, 12-/14-/16-Bit, Serial Input, Unipolar/Bipolar, Voltage Output DACs |
发布紧急采购，3分钟左右您将得到回复。