- 您现在的位置：买卖IC网 > PDF目录19638 > AD595CQ (Analog Devices Inc)IC THERMOCOUPLE A W/COMP 14CDIP PDF资料下载
参数资料
| 型号： | AD595CQ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/8页 |
| 文件大小： | 136K |
| 描述： | IC THERMOCOUPLE A W/COMP 14CDIP |
| 标准包装： | 25 |
| 功能： | 热电偶放大器 |
| 传感器类型： | 外部 |
| 精确度： | ±1°C（最小值） |
| 拓扑： | 冰点补偿，过载检测 |
| 输出类型： | 电压 |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 5 V ~ ±15 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 14-CDIP（0.300"，7.62mm） |
| 供应商设备封装： | 14-CDIP |
| 包装： | 管件 |
| 产品目录页面： | 797 (CN2011-ZH PDF) |
AD594/AD595
REV. C
7
ALARM CIRCUIT
In all applications of the AD594/AD595 the ALM connection,
Pin 13, should be constrained so that it is not more positive
than (V+) 4 V. This can be most easily achieved by connect-
ing Pin 13 to either common at Pin 4 or V at Pin 7. For most
applications that use the alarm signal, Pin 13 will be grounded
and the signal will be taken from +ALM on Pin 12. A typical
application is shown in Figure 10.
In this configuration the alarm transistor will be off in normal
operation and the 20 k pull up will cause the +ALM output on
Pin 12 to go high. If one or both of the thermocouple leads are
interrupted, the +ALM pin will be driven low. As shown in Fig-
ure 10 this signal is compatible with the input of a TTL gate
which can be used as a buffer and/or inverter.
CONSTANTAN
(ALUMEL)
IRON
(CHROMEL)
+5V
ALARM
TTL GATE
20k
ALARM OUT
GND
OVERLOAD
DETECT
G
TC
+TC
1 2
3
4
5
6
7
13
12
11
10
AD594/
AD595
14
ICE
POINT
COMP.
+A
9
8
G
10mV/C
Figure 10. Using the Alarm to Drive a TTL Gate
( Grounded Emitter Configuration)
Since the alarm is a high level output it may be used to directly
drive an LED or other indicator as shown in Figure 11.
CONSTANTAN
(ALUMEL)
IRON
(CHROMEL)
COMMON
LED
270
V+
OVERLOAD
DETECT
G
TC
+TC
1
2
3
4
5
6
7
13
12
11
10
AD594/
AD595
14
ICE
POINT
COMP.
+A
9
8
G
10mV/C
Figure 11. Alarm Directly Drives LED
A 270 & series resistor will limit current in the LED to 10 mA,
but may be omitted since the alarm output transistor is current
limited at about 20 mA. The transistor, however, will operate in
a high dissipation mode and the temperature of the circuit will
rise well above ambient. Note that the cold junction compensa-
tion will be affected whenever the alarm circuit is activated. The
time required for the chip to return to ambient temperature will
depend on the power dissipation of the alarm circuit, the nature
of the thermal path to the environment and the alarm duration.
The alarm can be used with both single and dual supplies. It
can be operated above or below ground. The collector and emit-
ter of the output transistor can be used in any normal switch
configuration. As an example a negative referenced load can be
driven from ALM as shown in Figure 12.
CONSTANTAN
(ALUMEL)
IRON
(CHROMEL)
+10V
GND
ALARM
RELAY
12V
OVERLOAD
DETECT
G
TC
+TC
1
2
3
4
5
6
7
13
12
11
10
AD594/
AD595
14
ICE
POINT
COMP.
+A
9
8
G
10mV/C
Figure 12. ALM Driving A Negative Referenced Load
The collector (+ALM) should not be allowed to become more
positive than (V) +36 V, however, it may be permitted to be
more positive than V+. The emitter voltage (ALM) should be
constrained so that it does not become more positive than 4
volts below the V+ applied to the circuit.
Additionally, the AD594/AD595 can be configured to produce
an extreme upscale or downscale output in applications where
an extra signal line for an alarm is inappropriate. By tying either
of the thermocouple inputs to common most runaway control
conditions can be automatically avoided. A +IN to common
connection creates a downscale output if the thermocouple opens,
while connecting IN to common provides an upscale output.
CELSIUS THERMOMETER
The AD594/AD595 may be configured as a stand-alone Celsius
thermometer as shown in Figure 13.
+5V TO +15V
OUTPUT
10mV/C
GND
T 1 V
OVERLOAD
DETECT
G
TC
+TC
1
2
3
4
5
6
7
13
12
11
10
AD594/
AD595
14
ICE
POINT
COMP.
+A
9
8
G
Figure 13. AD594/AD595 as a Stand-Alone Celsius
Thermometer
Simply omit the thermocouple and connect the inputs (Pins 1
and 14) to common. The output now will reflect the compensa-
tion voltage and hence will indicate the AD594/AD595
temperature with a scale factor of 10 mV/癈. In this three termi-
nal, voltage output, temperature sensing mode, the AD594/
AD595 will operate over the full military 55癈 to +125癈 tem-
perature range.
相关PDF资料 |
PDF描述 |
|---|---|
| M5-320/192-10SAC | IC CPLD ISP 320MC 192IO 256SBGA |
| TAJS224M020RNJ | CAP TANT 0.22UF 20V 20% 1206 |
| TAJT156K004RNJ | CAP TANT 15UF 4V 10% 1210 |
| VE-BTV-CY-F3 | CONVERTER MOD DC/DC 5.8V 50W |
| VE-BTV-CY-F2 | CONVERTER MOD DC/DC 5.8V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD596 | 制造商:AD 制造商全称:Analog Devices 功能描述:Thermocouple Conditioner and Setpoint Controller |
| AD-5960S | 制造商:BOTHHAND 制造商全称:Bothhand USA, LP. 功能描述:ADSL LINE TRANSFORMER |
| AD-5961S | 制造商:BOTHHAND 制造商全称:Bothhand USA, LP. 功能描述:ADSL LINE TRANSFORMER |
| AD596AH | 制造商:Analog Devices 功能描述:Temp Sensor Analog 10-Pin TO-100 制造商:Analog Devices 功能描述:Temperature Sensor IC Package/Case:TO-10 |
发布紧急采购，3分钟左右您将得到回复。