参数资料
| 型号： | AD600JRZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/33页 |
| 文件大小： | 0K |
| 描述： | IC AMP VGA DUAL LN 50MA 16SOIC |
| 标准包装： | 1 |
| 系列： | X-AMP® |
| 放大器类型： | 可变增益 |
| 电路数： | 2 |
| 转换速率： | 275 V/µs |
| -3db带宽： | 35MHz |
| 电流 - 输入偏压： | 350nA |
| 电流 - 电源： | 11mA |
| 电流 - 输出 / 通道： | 50mA |
| 电压 - 电源，单路/双路(±)： | ±4.75 V ~ 5.25 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
AD600/AD602
Rev. F | Page 16 of 32
REALIZING OTHER GAIN RANGES
Larger gain ranges can be accommodated by cascading
amplifiers. Combinations built by cascading two amplifiers
include 20 dB to +60 dB (using one AD602), 10 dB to +70 dB
(using of an AD602 followed by of an AD600), and 0 dB to
80 dB (using one AD600). In multiple-channel applications,
extra protection against oscillation can be provided by using
amplifier sections from different packages.
ULTRALOW NOISE VCA
The two channels of the AD600 or AD602 can operate in
parallel to achieve a 3 dB improvement in noise level, providing
1 nV/√Hz without any loss of gain accuracy or bandwidth.
In the simplest case, as shown in Figure 35, the signal inputs,
A1HI and A2HI, are tied directly together. The outputs, A1OP
and A2OP, are summed via R1 and R2 (100 Ω each), and the
control inputs, C1HI/C2HI and C1LO/C2LO, operate in
parallel. Using these connections, both the input and output
resistances are 50 Ω. Thus, when driven from a 50 Ω source and
terminated in a 50 Ω load, the gain is reduced by 12 dB, so the
gain range becomes –12 dB to +28 dB for the AD600 and 22 dB
to +18 dB for the AD602. The peak input capability remains
unaffected (1 V rms at the IC pins, or 2 V rms from an
unloaded 50 Ω source). The loading on each output, with a
50 Ω load, is effectively 200 Ω because the load current is
shared between the two channels, so the overall amplifier still
meets its specified maximum output and distortion levels for a
200 Ω load. This amplifier can deliver a maximum sine wave
power of 10 dBm to the load.
VPOS
VNEG
100
100
50
GAIN-CONTROL
VOLTAGE
VG
–+
VIN
VOUT
1
2
3
4
5
6
16
15
14
13
12
11
7
8
10
9
REF
A1
A2
AD600 OR
AD602
+
–
C1HI
A1CM
A1OP
A2OP
A2CM
C1LO
A1HI
A1LO
GAT1
A2LO
A2HI
+
C2HI
C2LO
GAT2
+5V
–5V
00
53
8-
0
33
Figure 35. An Ultralow Noise VCA Using the AD600 or AD602
LOW NOISE, 6 dB PREAMPLIFIER
In some ultrasound applications, a high input impedance
preamplifier is needed to avoid the signal attenuation that
results from loading the transducer by the 100 Ω input resistance
of the X-AMP. High gain cannot be tolerated because the
peak transducer signal is typically ±0.5 V, whereas the peak
input capability of the AD600 or AD602 is only slightly more
than ±1 V. A gain of 2 is a suitable choice. It can be shown that,
if the preamplifier’s overall referred-to-input (RTI) noise is the
same as that due to the X-AMP alone (1.4 nV/√Hz), the input
noise of nX2 preamplifier must be √(3/4) times as large, that is,
1.2 nV/√Hz.
+5V
–5V
+5V
–5V
1F
0.1F
VIN
INPUT
GROUND
OUTPUT
GROUND
R1
49.9
R2
174
R5
42.2
R3
562
R7
174
R8
49.9
Q1
MRF904
Q2
MM4049
100
RIN OF X-AMP
R6
562
1F
R4
42.2
1F
00
53
8-
0
34
Figure 36. A Low Noise Preamplifier for the AD600/AD602
An inexpensive circuit using complementary transistor types
determined by the ratio of the net collector load resistance to
the net emitter resistance. It is an open-loop amplifier. The gain
is ×2 (6 dB) only into a 100 Ω load, assumed to be provided by
the input resistance of the X-AMP; R2 and R7 are in shunt with
this load, and their value is important in defining the gain. For
small-signal inputs, both transistors contribute an equal trans-
conductance that is rendered less sensitive to signal level by the
emitter resistors, R4 and R5. They also play a dominant role in
setting the gain.
相关PDF资料 |
PDF描述 |
|---|---|
| 68488-436HLF | BERGSTIK II SR RIGHT ANGLE |
| AD602AR-REEL | IC AMP VGA DUAL LN 50MA 16SOIC |
| 69133-472HLF | BERGSTIK II .100" DR STRAIGHT |
| AD600AR-REEL | IC AMP VGA DUAL LN 50MA 16SOIC |
| MTSW-116-07-G-S-210 | CONN HEADER 16POS .100" STR GOLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD600JRZ | 制造商:Analog Devices 功能描述:IC, VARIABLE GAIN AMP, 35MHZ, 1DB SOIC16 |
| AD600JRZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual, Low Noise, Wideband Variable Gain Amplifiers |
| AD600JRZ-R7 | 功能描述:IC AMP VGA DUAL LN 50MA 16SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:X-AMP® 标准包装:2,500 系列:Excalibur™ 放大器类型:J-FET 电路数:1 输出类型:- 转换速率:45 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:20pA 电压 - 输入偏移:490µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
| AD600JRZ-RL | 功能描述:IC AMP VGA DUAL LN 50MA 16SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:X-AMP® 标准包装:2,500 系列:Excalibur™ 放大器类型:J-FET 电路数:1 输出类型:- 转换速率:45 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:20pA 电压 - 输入偏移:490µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
| AD-600-L | 制造商:Thomas & Betts 功能描述: |
发布紧急采购，3分钟左右您将得到回复。