参数资料
| 型号： | AD632TD |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/13页 |
| 文件大小： | 0K |
| 描述： | IC MULTIPLIER MONO PREC 14-CDIP |
| 标准包装： | 1 |
| 功能： | 模拟乘法器/除法器 |
| 位元/级数： | 四象限 |
| 封装/外壳： | 14-CDIP（0.300"，7.62mm） |
| 供应商设备封装： | 14-CDIP |
| 包装： | 管件 |
AD632
Data Sheet
Rev. D | Page 8 of 12
OPERATION AS A MULTIPLIER
Figure 7 shows the basic connection for multiplication. Note
that the circuit meets all specifications without trimming.
Figure 7. Basic Multiplier Connection
When needed, the user can reduce ac feedthrough to a minimum
(as in a suppressed carrier modulator) by applying an external
trim voltage (±30 mV range required) to the X or Y input. Figure 4
shows the typical ac feedthrough with this adjustment mode.
Note that the feedthrough of the Y input is a factor of 10 lower
than that of the X input and is to be used for applications where
null suppression is critical.
signal into the output. In this mode, the output amplifier behaves
as a voltage follower with a 1 MHz small signal bandwidth and
a 20 V/μs slew rate. Always reference this terminal to the ground
point of the driven system, particularly if this is remote. Like-
wise, reference the differential inputs to their respective signal
common potentials to realize the full accuracy of the AD632.
A much lower scaling voltage can be achieved without any reduc-
tion of input signal range using a feedback attenuator, as shown
that the circuit can exhibit a maximum gain of 10. This connection
results in a reduction of bandwidth to about 80 kHz without the
peaking capacitor, CF. In addition, the output offset voltage is
increased by a factor of 10 making external adjustments necessary
in some applications.
Feedback attenuation also retains the capability for adding a
signal to the output. Signals can be applied to the Z terminal,
where they are amplified by 10, or to the common ground
connection where they are amplified by 1. Input signals can
also be applied to the lower end of the 2.7 kΩ resistor, giving a
gain of +9.
Figure 8. Connections for Scale Factor of Unity
X1
+VS
X2
VOS
OUT
Z1
Z2
Y1
Y2
–VS
–15V
+15V
X INPUT
±10V FS
±12V PK
Y INPUT
±10V FS
±12V PK
OUTPUT, ±12V PK
(X1 – X2) (Y1 – Y2)
OPTIONAL SUMMING
INPUT, Z, ±10V PK;
VOS TERMINAL
NOT USED
10
+ Z2
=
09
04
0-
00
8
X1
+VS
X2
OUT
Z1
Z2
VOS
Y1
Y2
–VS
–15V
+15V
X INPUT
±10V FS
±12V PK
Y INPUT
±10V FS
±12V PK
OUTPUT, ±12V PK
= (X1 – X2) (Y1 – Y2)
(SCALE = 1)
09
04
0-
00
9
相关PDF资料 |
PDF描述 |
|---|---|
| AD633JR | IC ANALOG MULTIPLIER 8-SOIC |
| AD7148ACPZ-1REEL | IC CAP-TO-DGTL CONV PROG 16LFCSP |
| AD734BQ | IC MULTIPLIER 4-QUADRANT 14-CDIP |
| AD790SQ | IC COMPARATOR PREC W/LATCH 8CDIP |
| AD8013ANZ | IC OPAMP SINGLE 14DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD632TD/883B | 功能描述:增效器/分频器 MULTIPLIER IC RoHS:否 制造商:Texas Instruments 产品:Multiplier 逻辑系列: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:Through Hole 封装 / 箱体:PDIP-14 |
| AD632TH | 功能描述:IC PREC MULTIPLIER MONO TO100-10 RoHS:否 类别:集成电路 (IC) >> 线性 - 模拟乘法器，除法器 系列:- 标准包装:25 系列:HA 功能:模拟乘法器 位元/级数:四象限 封装/外壳:16-CDIP（0.300"，7.62mm） 供应商设备封装:16-CDIP 侧面铜焊 包装:管件 |
| AD632TH/883B | 功能描述:增效器/分频器 MULTIPLIER IC RoHS:否 制造商:Texas Instruments 产品:Multiplier 逻辑系列: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:Through Hole 封装 / 箱体:PDIP-14 |
| AD633 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Cost Analog Multiplier |
| AD633AN | 制造商:Analog Devices 功能描述:Analog Multiplier 4-Bit 8-Pin PDIP |
发布紧急采购，3分钟左右您将得到回复。