- 您现在的位置：买卖IC网 > PDF目录16774 > AD680JR (Analog Devices Inc)IC VREF SERIES PREC 2.5V 8-SOIC PDF资料下载
参数资料
| 型号： | AD680JR |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/12页 |
| 文件大小： | 0K |
| 描述： | IC VREF SERIES PREC 2.5V 8-SOIC |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 标准包装： | 98 |
| 基准类型： | 串联，精度 |
| 输出电压： | 2.5V |
| 容差： | ±0.4% |
| 温度系数： | 25ppm/°C |
| 输入电压： | 4.5 V ~ 36 V |
| 通道数： | 1 |
| 电流 - 静态： | 250µA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 管件 |
AD680
THEORY OF OPERATION
Band gap references are the high performance solution for low
supply voltage operation. A typical precision band gap consists
of a reference core and buffer amplifier. Based on a new, pat-
ented band gap reference design (Figure 5), the AD680 merges
the amplifier and the core band gap function to produce a
compact, complete precision reference.
Central to the device is a high gain amplifier with an intentionally
large proportional to absolute temperature (PTAT) input offset.
This offset is controlled by the area ratio of the amplifier input
pair, Q1 and Q2, and is developed across Resistor R1. Transistor
Q12’s base emitter voltage has a complementary to absolute
temperature (CTAT) characteristic. Resistor R2 and the parallel
combination of Resistor R3 and Resistor R4 “multiply” the PTAT
voltage across the R1 resistor. Trimming the R3 and R4 resistors
to the proper ratio produces a temperature invariant of 2.5 V at
the output. The result is an accurate, stable output voltage
accomplished with a minimum number of components.
+V IN
Reference outputs are frequently required to handle fast
transients caused by input switching networks, commonly
found in ADCs and measurement instrumentation equipment.
Many of the dynamic problems associated with this situation
can be minimized with a few simple techniques. Using a series
resistor between the reference output and the load tends to
“decouple” the reference output from the transient source, or a
relatively large capacitor connected from the reference output to
ground can serve as a charge storage element to absorb and
deliver charge as required by the dynamic load. A 50 nF capaci-
tor is recommended for the AD680 in this case; this is large
enough to store the required charge, but small enough not to
disrupt the stability of the reference.
The 8-lead PDIP and 8-lead SOIC packaged versions of the
AD680 also provide a temperature output pin. The voltage on
this pin is nominally 596 mV at 25°C. This pin provides an
output linearly proportional to temperature with a
characteristic of 2 mV/°C.
NOISE PERFORMANCE
Q9
Q8
Q11
The noise generated by the AD680 is typically less than 8 μV p-p
over the 0.1 Hz to 10 Hz band. Figure 6 shows the 0.1 Hz to 10 Hz
Q3
Q1
1 ×
Q4
Q5
R1
V OUT
noise of a typical AD680. The noise measurement is made with a
band-pass filter made of a 1-pole high-pass filter, with a corner
frequency at 0.1 Hz, and a 2-pole low-pass filter, with a corner
frequency at 12.6 Hz, to create a filter with a 9.922 Hz bandwidth.
R5
Q10
Q2
8 ×
C1
R2
Q12
R3
1s
100
TEMP
R6
Q6
Q7
R4
90
R7
GND
Figure 5. Schematic Diagram
APPLYING THE AD680
The AD680 is simple to use in virtually all precision reference
applications. When power is applied to +V IN and the GND pin
is tied to ground, V OUT provides a 2.5 V output. The AD680
typically requires less than 250 μA of current when operating
from a supply of 4.5 V to 36 V.
To operate the AD680, the +V IN pin must be bypassed to the
GND pin with a 0.1 μF capacitor tied as close to the AD680 as
5 μ V
10
0%
Figure 6. 0.1 Hz to 10 Hz Noise
Noise in a 300 kHz bandwidth is approximately 800 μV p-p.
possible. Although the ground current for the AD680 is small,
typically 195 μA, a direct connection should be made between
the AD680 GND pin and the system ground plane.
Rev. H | Page 6 of 12
相关PDF资料 |
PDF描述 |
|---|---|
| 0982660225 | CBL 20POS 0.5MM JMPR TYPE A 1' |
| GSC05DRTS-S93 | CONN EDGECARD 10POS DIP .100 SLD |
| B78108S1683J | CHOKE RF 68UH 410MA AXIAL |
| AFK475M80D16T-F | CAP ALUM 4.7UF 80V 20% SMD |
| V300C28T75BF2 | CONVERTER MOD DC/DC 28V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD680JR-REEL7 | 功能描述:IC VREF SERIES PREC 2.5V 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电压基准 系列:- 标准包装:3,000 系列:- 基准类型:旁路，精度 输出电压:5V 容差:±0.5% 温度系数:100ppm/°C 输入电压:- 通道数:1 电流 - 阴极:80µA 电流 - 静态:- 电流 - 输出:15mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:TO-236-3，SC-59，SOT-23-3 供应商设备封装:SOT-23-3 包装:带卷 (TR) 其它名称:LM4040CIM3-5.0MLTRLM4040CIM3-5.0MLTR-ND |
| AD680JRZ | 功能描述:IC VREF SERIES PREC 2.5V 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电压基准 系列:- 标准包装:3,000 系列:- 基准类型:旁路，精度 输出电压:3V 容差:±0.5% 温度系数:100ppm/°C 输入电压:- 通道数:1 电流 - 阴极:82µA 电流 - 静态:- 电流 - 输出:15mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-TSSOP（5 引线），SC-88A，SOT-353 供应商设备封装:SC-70-5 包装:带卷 (TR) 其它名称:296-20888-2 |
| AD680JRZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, Low Cost 2.5 V Reference |
| AD680JRZ-REEL7 | 功能描述:IC VREF SERIES PREC 2.5V 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电压基准 系列:- 产品培训模块:Voltage Reference Basics 标准包装:100 系列:- 基准类型:旁路，精度 输出电压:4.096V 容差:±0.075% 温度系数:50ppm/°C 输入电压:- 通道数:1 电流 - 阴极:1µA 电流 - 静态:- 电流 - 输出:10mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 |
| AD680JRZ-REEL71 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, Low Cost 2.5 V Reference |
发布紧急采购，3分钟左右您将得到回复。