- 您现在的位置：买卖IC网 > PDF目录9521 > AD7156BCPZ-REEL7 (Analog Devices Inc)IC CDC 2CH 12BIT 1.8V 10LFCSP PDF资料下载
参数资料
| 型号： | AD7156BCPZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 15/28页 |
| 文件大小： | 0K |
| 描述： | IC CDC 2CH 12BIT 1.8V 10LFCSP |
| 标准包装： | 1 |
| 类型： | 电容数字转换器 |
| 分辨率（位）： | 12 b |
| 采样率（每秒）： | 100k |
| 数据接口： | 串行 |
| 电压电源： | 单电源 |
| 电源电压： | 1.8 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘，CSP |
| 供应商设备封装： | 10-LFCSP-WD（3x3） |
| 包装： | 标准包装 |
| 产品目录页面： | 781 (CN2011-ZH PDF) |
| 其它名称： | AD7156BCPZ-REEL7DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7156
Rev. 0 | Page 22 of 28
SERIAL INTERFACE
The AD7156 supports an I2C-compatible, 2-wire serial inter-
face. The two wires on the serial bus (interface) are called SCL
(clock) and SDA (data). These two wires carry all addressing,
control, and data information one bit at a time over the bus to
all connected peripheral devices. The SDA wire carries the data,
while the SCL wire synchronizes the sender and receiver during
the data transfer. The devices on the bus are classified as either
master or slave devices. A device that initiates a data transfer
message is called a master, whereas a device that responds to
this message is called a slave.
To control the AD7156 device on the bus, the following
protocol must be utilized. First, the master initiates a data
transfer by establishing a start condition, defined by a high-
to-low transition on SDA while SCL remains high. This
indicates that the start byte follows. This 8-bit start byte is
made up of a 7-bit address plus an R/W bit indicator.
All peripherals connected to the bus respond to the start
condition and shift in the next eight bits (7-bit address + R/W
bit). The bits arrive MSB first. The peripheral that recognizes
the transmitted address responds by pulling the data line low
during the ninth clock pulse. This is known as the acknowledge
bit. All other devices withdraw from the bus at this point and
maintain an idle condition. An exception to this is the general
call address, which is described in the General Call section. In
the idle condition, the device monitors the SDA and SCL lines
waiting for the start condition and the correct address byte.
The R/W bit determines the direction of the data transfer.
A Logic 0 LSB in the start byte means that the master writes
information to the addressed peripheral. In this case, the
AD7156 becomes a slave receiver. A Logic 1 LSB in the
start byte means that the master reads information from
the addressed peripheral. In this case, the AD7156 becomes
a slave transmitter. In all instances, the AD7156 acts as a
standard slave device on the serial bus.
The start byte address for the AD7156 is 0x90 for a write and
0x91 for a read.
READ OPERATION
When a read is selected in the start byte, the register that is
currently addressed by the address pointer is transmitted to the
SDA line by the AD7156. This is then clocked out by the master
device, and the AD7156 awaits an acknowledge from the master.
If an acknowledge is received from the master, the address
autoincrementer automatically increments the address pointer
register and outputs the next addressed register content to the
SDA line for transmission to the master. If no acknowledge is
received, the AD7156 returns to the idle state and the address
pointer is not incremented. The address pointers’ autoincrementer
allows block data to be written to or read from the starting address
and subsequent incremental addresses.
In continuous conversion mode, the address pointers’ auto-
incrementer should be used for reading a conversion result.
This means that the two data bytes should be read using one
multibyte read transaction rather than two separate single byte
transactions. The single byte data read transaction may result in
the data bytes from two different results being mixed. The same
applies for four data bytes if both capacitive channels are enabled.
The user can also access any unique register (address) on a
one-to-one basis without having to update all the registers.
The address pointer register contents cannot be read.
If an incorrect address pointer location is accessed or if the
user allows the autoincrementer to exceed the required register
address, the following applies:
In read mode, the AD7156 continues to output various
internal register contents until the master device issues
a no acknowledge, start, or stop condition. The address
pointers’ autoincrementer contents are reset to point to
the status register at the 0x00 address when a stop condition
is received at the end of a read operation. This allows the
status register to be read (polled) continually without
having to constantly write to the address pointer.
In write mode, the data for the invalid address is not
loaded into the AD7156 registers, but an acknowledge
is issued by the AD7156.
WRITE OPERATION
When a write is selected, the byte following the start byte is
always the register address pointer (subaddress) byte, which
points to one of the internal registers on the AD7156. The
address pointer byte is automatically loaded into the address
pointer register and acknowledged by the AD7156. After the
address pointer byte acknowledge, a stop condition, a repeated
start condition, or another data byte can follow from the master.
A stop condition is defined by a low-to-high transition on SDA
while SCL remains high. If a stop condition is encountered by
the AD7156, it returns to its idle condition and the address
pointer is reset to 0x00.
If a data byte is transmitted after the register address pointer
byte, the AD7156 loads this byte into the register that is cur-
rently addressed by the address pointer register and sends
an acknowledge, and the address pointer autoincrementer
automatically increments the address pointer register to the
next internal register address. Thus, subsequent transmitted
data bytes are loaded into sequentially incremented addresses.
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/24KE6SN | CONN RCPT 6POS JAM NUT W/SCKT |
| M83723/83A12126 | CONN RCPT 12POS WALL MT W/PINS |
| MS27473E18A32PD | CONN PLUG 32POS STRAIGHT W/PINS |
| MS3456W18-4S | CONN PLUG 4POS STRAIGHT W/SCKT |
| MS27474E16A26S | CONN RCPT 26POS JAM NUT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7160ACBZ-U3 | 制造商:Analog Devices 功能描述: |
| AD7161BCDZ-1WP | 制造商:Analog Devices 功能描述: |
| AD7166ACPZ-RL7 | 制造商:Analog Devices 功能描述:- Tape and Reel |
| AD-716J4310J-1 | 功能描述:Adapter Coaxial Connector 7/16 Jack, Female Socket To 4.3/10 Jack, Female Socket 50 Ohm 制造商:amphenol-rf division 系列:- 包装:散装 零件状态:有效 适配器类型:插孔至插孔 适配器系列:7/16 DIN 至 4.3/10 中性:母形至母形 转换自（适配器端）:7/16 插孔，母插口 转换至（适配器端）:4.3/10 插孔，母插口 转换类型:跨系列 阻抗:50 欧姆 样式:直形 安装类型:自由悬挂 频率 - 最大值:6GHz 侵入防护:- 特性:- 基体材料:黄铜 基体表面:白青铜 介电材料:聚四氟乙烯（PTFE） 中心触头材料:铜铍 中心触头镀层:银 配接次数:500 标准包装:25 |
| AD-716J4310P-1 | 功能描述:Adapter Coaxial Connector 7/16 Jack, Female Socket To 4.3/10 Plug, Male Pin 50 Ohm 制造商:amphenol-rf division 系列:- 包装:散装 零件状态:有效 适配器类型:插头至插孔 适配器系列:7/16 DIN 至 4.3/10 中性:母型至公型 转换自（适配器端）:7/16 插孔，母插口 转换至（适配器端）:4.3/10 插头，公引脚 转换类型:跨系列 阻抗:50 欧姆 样式:直形 安装类型:自由悬挂 频率 - 最大值:6GHz 侵入防护:- 特性:- 基体材料:黄铜 基体表面:白青铜 介电材料:聚四氟乙烯（PTFE） 中心触头材料:铜铍 中心触头镀层:银 配接次数:500 标准包装:25 |
发布紧急采购，3分钟左右您将得到回复。