- 您现在的位置：买卖IC网 > PDF目录223307 > AD7322 (Atmel Corp.) Software Selectable True Bipolar Input, 2-Channel, 12-Bit Plus Sign ADC PDF资料下载
参数资料
| 型号： | AD7322 |
| 厂商： | Atmel Corp. |
| 英文描述： | Software Selectable True Bipolar Input, 2-Channel, 12-Bit Plus Sign ADC |
| 中文描述： | 软件可选真双极性输入，2通道，12位ADC的加号 |
| 文件页数： | 3/18页 |
| 文件大小： | 901K |
| 代理商： | AD7322 |
Preliminary Technical Data
AD7322
D
VDD
C2
R1
Vin0
VSS
C1
Figure 10. Equivalent Analog Input Circuit-(Single Ended)
D
VDD
C2
R1
Vin+
VSS
C1
D
VDD
C2
R1
Vin-
VSS
C1
Figure 11. Equivalent Analog Input Circuit-(Differential)
Care should be taken to ensure the Analog Input never exceeds
the VDD and VSS supply rails by more than 300 mV. This will
cause the diodes to become forward biased and start
conducting into either the VDD or VSS rails. These diodes can
conduct up to 10 mA without causing irreversible damage to
the part.
The Capacitor C1, in
and
is typically 4 pF
and can primarily be attributed to pin capacitance. The resistor
R1, is a lumped component made up of the on-resistance of the
input multiplexer and the track-and-hold switch. The Capacitor
C2, is the sampling capacitor, its capacitance will vary
depending on the Analog input range selected.
Track-and-Hold Section
The Track-and-Hold on the Analog Input of the AD7322 allows
the ADC to accurately convert an input sine wave of full scale
amplitude to 13-Bit accuracy. The input bandwidth of the
Track-and-Hold is greater than the Nyquist rate of the ADC ,
the AD7322 can handle frequencies up to 13 MHz.
The Track-and-Hold enters its tracking mode on the 15th SCLK
falling edge after the CS falling edge. The time required to
acquire an input signal will depend on how quickly the
sampling capacitor is charged. With zero source impedance 300
ns will be sufficient to acquire the signal to the 13-bit level.
The acquisition time required is calculated using the following
formula:
tACQ = 10 x ((RSOURCE + R) C)
where C is the Sampling Capacitance and R is the resistance
seen by the track-and-hold amplifier looking back on the input.
For the AD7322, the value of R will include the on-resistance of
the input multiplexer. The value of R is typically 300 . RSOURCE
should include any extra source impedance on the Analog
input.
TYPICAL CONNECTION DIAGRAM
Figure 12. Typical Connection Diagram
shows a typical connection diagram for the AD7322.
In this configuration the AGND pin is connected to the Analog
ground plane of the system. The DGND pin is connected to the
Digital ground plane of the system. The Analog Inputs on the
AD7322 can be configured to operate in Single Ended, True
Differential or Pseudo Differential Mode. The AD7322 can
operate with either the internal or an external reference. In
, the AD7322 is configured to operate with the internal
2.5V reference. A 470 nF decoupling capacitor is required when
operating with the internal reference.
The VCC pin can be connected to either a 3V or a 5V supply
voltage. The VDD and VSS are the dual supplies for the high
voltage analog input structures. The voltage on these pins must
be equal to or greater than the highest analog input range
selected on the analog input channels, see
for more
information. The VDRIVE pin is connected to the supply voltage
of the microprocessor. The voltage applied to the VDRIVE input
controls the voltage at which the serial interface operates.
Rev. PrE | Page 11 of 18
相关PDF资料 |
PDF描述 |
|---|---|
| AD7322BRU | Software Selectable True Bipolar Input, 2-Channel, 12-Bit Plus Sign ADC |
| AD7858ARZ | 8-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO24 |
| AD8185ARU-REEL | TRIPLE 2-CHANNEL, VIDEO MULTIPLEXER, PDSO24 |
| AD8617ACPZ-R2 | DUAL OP-AMP, 2200 uV OFFSET-MAX, 0.35 MHz BAND WIDTH, PDSO8 |
| AD8617ACPZ-R7 | DUAL OP-AMP, 2200 uV OFFSET-MAX, 0.35 MHz BAND WIDTH, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7322BRU | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Software Selectable True Bipolar Input, 2-Channel, 12-Bit Plus Sign ADC |
| AD7322BRUZ | 功能描述:IC ADC 12BIT+ SAR 2CHAN 14TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7322BRUZ-REEL | 功能描述:IC ADC 12BIT+SAR 2CHAN 14-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7322BRUZ-REEL7 | 功能描述:IC ADC 12BIT+ SAR 2CHAN 14TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7322LYRU | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。