参数资料
型号: AD7470ARU-REEL7
厂商: Analog Devices Inc
文件页数: 4/21页
文件大小: 0K
描述: IC ADC 10BIT PARALLEL 24-TSSOP
产品变化通告: Product Discontinuance 27/Oct/2011
标准包装: 1,000
位数: 10
采样率(每秒): 1.75M
数据接口: 并联
转换器数目: 1
功率耗散(最大): 12mW
电压电源: 模拟和数字
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 24-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 24-TSSOP
包装: 带卷 (TR)
输入数目和类型: 1 个单端,单极
REV. B
AD7470/AD7472
–11–
ADC TRANSFER FUNCTION
The output coding of the AD7470/AD7472 is straight binary.
The designed code transitions occur midway between succes-
sive integer LSB values (0.5 LSB, 1.5 LSB, etc). The LSB
size is equal to (REF IN)/4096 for the AD7472 and to (REF
IN)/1024 for the AD7470. The ideal transfer characteristic for
the AD7472 is shown in Figure 6.
111...111
111...110
111...000
011...111
000...010
000...001
000...000
ADC
CODE
0V 0.5LSB
VREF –1.5LSB
ANALOG INPUT
1LSB = VREF/4096
Figure 6. Transfer Characteristic for 12 Bits
AC ACQUISITION TIME
In ac applications it is recommended to always buffer analog
input signals. The source impedance of the drive circuitry must
be kept as low as possible to minimize the acquisition time of
the ADC. Large values of impedance at the VIN pin of the ADC
will cause the THD to degrade at high input frequencies.
The AD8021, AD8047, AD8051, AD9631, and AD797 are
some of the op amps that could be used to buffer the analog
input. Figure 7 shows the AD7470/AD7472 performance for
some of those recommended input buffers.
TYPICAL AMPLIFIER
INPUT
SNR
THD
CURRENT
BUFFERS
500kHz
CONSUMPTION
AD8047
70
78
5.8mA
AD9631
69.5
80
17mA
AD8051
68.6
78
4.4mA
AD797
70
84
8.2mA
AD7470/AD7472
DYNAMIC
PERFORMANCE
SPECIFICATIONS
Figure 7. Recommended Input Buffers
Reference Input
The following references are best suited for use with the
AD7470/AD7472.
ADR291
AD780
REF192
ADR421
For optimum performance, a 2.5 V reference is recommended.
The parts can function with a reference up to 3 V and down to
2 V, but the performance deteriorates.
DC ACQUISITION TIME
The ADC starts a new acquisition phase at the end of a conver-
sion and ends it on the falling edge of the
CONVST signal. At
the end of conversion there is a settling time associated with the
sampling circuit. This settling time lasts approximately 135 ns.
The analog signal on VIN is also being acquired during this
settling time; therefore, the minimum acquisition time needed is
approximately 135 ns.
Figure 8 shows the equivalent charging circuit for the sampling
capacitor when the ADC is in its acquisition phase. R3 repre-
sents the source impedance of a buffer amplifier or resistive
network, R1 is an internal switch resistance, R2 is for bandwidth
control, and C1 is the sampling capacitor. C2 is back-plate
capacitance and switch parasitic capacitance.
During the acquisition phase the sampling capacitor must be
charged to within
±1 LSB of its final value.
R3
R1
125
VIN
C1
22pF
C2
8pF
R2
636
Figure 8. Equivalent Sampling Circuit
ANALOG INPUT
Figure 9 shows the equivalent circuit of the analog input struc-
ture of the AD7470/AD7472. The two diodes, D1 and D2,
provide ESD protection for the analog inputs. The capacitor C3
is typically about 4 pF and can be primarily attributed to pin
capacitance. The resistor R1 is an internal switch resistance.
This resistor is typically about 125
. The capacitor C1 is the
sampling capacitor, while R2 is used for bandwidth control.
R1
125
VIN
C1
22pF
C2
8pF
R2
636
D1
D2
C3
4pF
VDD
Figure 9. Equivalent Analog Input Circuit
CLOCK SOURCES
The max CLK specification for the AD7470 is 30 MHz, and for
the AD7472, it is 26 MHz. These frequencies are not standard
off-the-shelf oscillator frequencies. Many manufacturers pro-
duce oscillator modules close to these frequencies; a typical one
being 25.175 MHz from IQD Limited. AEL Crystals Limited
produces a 25 MHz oscillator module in various packages. Crys-
tal oscillator manufacturers will produce 26 MHz and 30 MHz
oscillators to order. Of course any clock source can be used, not
just crystal oscillators.
相关PDF资料
PDF描述
MAX3241CWI+T IC TXRX RS-232 LP 28-SOIC
VI-23M-IU-F4 CONVERTER MOD DC/DC 10V 200W
MAX485EEPA+G104 IC TXRX RS485/RS422 8-DIP
MS27484E8B35SA CONN PLUG 6POS STRAIGHT W/SCKT
MS27484E20B35PC CONN PLUG 79POS STRAIGHT W/PINS
相关代理商/技术参数
参数描述
AD7470ARUZ 功能描述:IC ADC 10BIT PARALLEL 24-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率(每秒):1M 数据接口:串行,SPI? 转换器数目:1 功率耗散(最大):- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘(4x4) 包装:Digi-Reel® 输入数目和类型:8 个单端,单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6
AD7470ARUZ-REEL 功能描述:IC ADC 10BIT PARLLEL 24TSSOP T/R RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率(每秒):15 数据接口:MICROWIRE?,串行,SPI? 转换器数目:1 功率耗散(最大):480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN(5x7) 包装:带卷 (TR) 输入数目和类型:16 个单端,双极;8 个差分,双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
AD7470ARUZ-REEL7 功能描述:IC ADC 10BIT PARLLEL 24TSSOP T/R RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率(每秒):15 数据接口:MICROWIRE?,串行,SPI? 转换器数目:1 功率耗散(最大):480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN(5x7) 包装:带卷 (TR) 输入数目和类型:16 个单端,双极;8 个差分,双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
AD7472 制造商:未知厂家 制造商全称:未知厂家 功能描述:AD7470/AD7472: 1.75MSPS. 4mW 10-Bit/12-Bit SAR ADC Data Sheet (Rev. A. 3/00)
AD7472AR 功能描述:IC ADC 12BIT PARALLEL 24-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率(每秒):3M 数据接口:- 转换器数目:- 功率耗散(最大):- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:-