参数资料
型号: AD7478AAKSZ-500RL7
厂商: Analog Devices Inc
文件页数: 13/29页
文件大小: 0K
描述: IC ADC 8BIT 1MSPS SC70-6 T/R
标准包装: 1
位数: 8
采样率(每秒): 1M
数据接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
转换器数目: 1
功率耗散(最大): 17.5mW
电压电源: 单电源
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 6-TSSOP,SC-88,SOT-363
供应商设备封装: SC-70-6
包装: 标准包装
输入数目和类型: 1 个单端,单极
其它名称: AD7478AAKSZ-500RL7DKR
AD7478AAKSZ500RL7DKR
AD7478AAKSZ500RL7DKR-ND
AD7476A/AD7477A/AD7478A
Rev. F | Page 19 of 28
SDATA
SCLK
CS
1
10
12
14
16
AD7476A/AD7477A/AD7478A
02930-020
VALID DATA
Figure 20. Normal Mode Operation
THREE-STATE
SDATA
SCLK
CS
1
10
12
14
16
2
02930-021
Figure 21. Entering Power-Down Mode
INVALID DATA
SDATA
SCLK
CS
1
10
12
14
16
A
1
16
VALID DATA
THE PART IS FULLY
POWERED UP WITH
VIN FULLY ACQUIRED
THE PART
BEGINS TO
POWER UP
02930-022
Figure 22. Exiting Power-Down Mode
When power supplies are first applied to the AD7476A/AD7477A/
AD7478A, the ADC can power up in either the power-down or
normal modes. Because of this, it is best to allow a dummy cycle
to elapse to ensure that the part is fully powered up before
attempting a valid conversion. Likewise, if it is intended to keep
the part in the power-down mode while not in use and the user
wishes the part to power up in power-down mode, the dummy
cycle can be used to ensure that the device is in power-down by
executing a cycle such as that shown in Figure 22. Once supplies
are applied to the AD7476A/AD7477A/AD7478A, the power-up
time is the same as that when powering up from the power-down
mode. It takes approximately 1 μs to power up fully if the part
powers up in normal mode. It is not necessary to wait 1 μs before
executing a dummy cycle to ensure the desired mode of operation.
Instead, a dummy cycle can occur directly after power is
supplied to the ADC. If the first valid conversion is performed
directly after the dummy conversion, care must be taken to
ensure that an adequate acquisition time has been allowed. As
mentioned earlier, when powering up from the power-down
mode, the part returns to track upon the first SCLK edge
applied after the falling edge of CS. However, when the ADC
initially powers up after supplies are applied, the track-and-hold
is already in track. This means, assuming one has the facility to
monitor the ADC supply current, if the ADC powers up in the
desired mode of operation and thus a dummy cycle is not
required to change the mode, a dummy cycle is not required to
place the track-and-hold into track.
相关PDF资料
PDF描述
VE-B4P-MX-F1 CONVERTER MOD DC/DC 13.8V 75W
TMK063CK0R5DP-F CAP CER 0.5PF 25V C0K 0201
TMK063CK0R5CP-F CAP CER 0.5PF 25V C0K 0201
VE-B4P-MW CONVERTER MOD DC/DC 13.8V 100W
VE-B4N-MX-F3 CONVERTER MOD DC/DC 18.5V 75W
相关代理商/技术参数
参数描述
AD7478AAKSZ-500RL73 制造商:AD 制造商全称:Analog Devices 功能描述:2.35 V to 5.25 V, 1 MSPS, 12-/10-/8-Bit ADCs in 6-Lead SC70
AD7478AAKSZ-REEL 功能描述:IC ADC 8BIT 1MSPS SC70-6 T/R RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率(每秒):15 数据接口:MICROWIRE?,串行,SPI? 转换器数目:1 功率耗散(最大):480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN(5x7) 包装:带卷 (TR) 输入数目和类型:16 个单端,双极;8 个差分,双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
AD7478AAKSZ-REEL3 制造商:AD 制造商全称:Analog Devices 功能描述:2.35 V to 5.25 V, 1 MSPS, 12-/10-/8-Bit ADCs in 6-Lead SC70
AD7478AAKSZ-REEL7 功能描述:IC ADC 8BIT 1MSPS SC70-6 T/R RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率(每秒):15 数据接口:MICROWIRE?,串行,SPI? 转换器数目:1 功率耗散(最大):480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN(5x7) 包装:带卷 (TR) 输入数目和类型:16 个单端,双极;8 个差分,双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
AD7478AAKSZ-REEL73 制造商:AD 制造商全称:Analog Devices 功能描述:2.35 V to 5.25 V, 1 MSPS, 12-/10-/8-Bit ADCs in 6-Lead SC70