- 您现在的位置：买卖IC网 > PDF目录10195 > AD7610BCPZ-RL (Analog Devices Inc)IC ADC 16BIT 250KSPS 48-LFCSP PDF资料下载
参数资料
| 型号： | AD7610BCPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 250KSPS 48-LFCSP |
| 标准包装： | 2,500 |
| 系列： | PulSAR® |
| 位数： | 16 |
| 采样率（每秒）： | 250k |
| 数据接口： | 串行，并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 110mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 48-LFCSP-VQ（7x7） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个差分，单极；1 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD7610
Data Sheet
Rev. A | Page 24 of 32
8-Bit Interface (Master or Slave)
The BYTESWAP pin allows a glueless interface to an 8-bit bus.
As shown in Figure 38, when BYTESWAP is low, the LSB byte
is output on D[7:0] and the MSB is output on D[15:8]. When
BYTESWAP is high, the LSB and MSB bytes are swapped; the
LSB is output on D[15:8] and the MSB is output on D[7:0]. By
connecting BYTESWAP to an address line, the 16-bit data can
be read in two bytes on either D[15:8] or D[7:0]. This interface
can be used in both master and slave parallel reading modes.
CS
RD
BYTESWAP
PINS D[15:8]
PINS D[7:0]
HI-Z
HIGH BYTE
LOW BYTE
HIGH BYTE
HI-Z
t12
t13
06395-
038
Figure 38. 8-Bit and 16-Bit Parallel Interface
SERIAL INTERFACE
The AD7610 has a serial interface (SPI-compatible) multiplexed
on the data pins D[15:2]. The AD7610 is configured to use the
serial interface when SER/PAR is held high.
Data Interface
The AD7610 outputs 16 bits of data, MSB first, on the SDOUT pin.
This data is synchronized with the 16 clock pulses provided on
the SDCLK pin. The output data is valid on both the rising and
falling edge of the data clock.
Serial Configuration Interface
The AD7610 can be configured through the serial configuration
register only in serial mode as the serial configuration pins are
also multiplexed on the data pins D[15:12]. See the Hardware
Configuration section and Software Configuration section for
more information.
MASTER SERIAL INTERFACE
The pins multiplexed on D[10:2] and used for the master serial
interface are: DIVSCLK[0], DIVSCLK[1], EXT/INT, INVSYNC,
INVSCLK, RDC, SDOUT, SDCLK and SYNC.
Internal Clock (SER/PAR = High, EXT/INT = Low)
The AD7610 is configured to generate and provide the serial
data clock, SDCLK, when the EXT/INT pin is held low. The
AD7610 also generates a SYNC signal to indicate to the host
when the serial data is valid. The SDCLK, and the SYNC signals
can be inverted, if desired using the INVSCLK and INVSYNC
inputs, respectively. Depending on the input, RDC, the data can
be read during the following conversion or after each conver-
sion. Figure 39 and Figure 40 show detailed timing diagrams of
these two modes.
Read After Convert (RDC = Low, DIVSCLK[1:0] = [0 to 3])
Setting RDC = low, allows the read after conversion mode.
Since the AD7610 is limited to 250kSPS and the time between
conversions, t2 = 4s, this mode is the most recommended
serial mode. Unlike the other serial modes, the BUSY signal
returns low after the 16 data bits are pulsed out and not at the
end of the conversion phase, resulting in a longer BUSY width
(See Table 4 for BUSY timing specifications). The
DIVSCLK[1:0] inputs control the SDCLK period and SDOUT
data rate. As a result, the maximum throughput can only be
achieved in two of the DIVSCLK[1:0] settings. In this mode, the
AD7610 generates a discontinuous SDCLK however, a fixed
period and hosts supporting both SPI and serial ports can also
be used.
Read During Convert (RDC = High)
Setting RDC = high, allows the master read (previous conver-
sion result) during conversion mode. In this mode, the serial
clock and data toggle at appropriate instances, minimizing
potential feed through between digital activity and critical
conversion decisions. In this mode, the SDCLK period changes
since the LSBs require more time to settle and the SDCLK is
derived from the SAR conver-sion cycle. In this mode, the
AD7610 generates a discontinuous SDCLK of two different
periods and the host should use an SPI interface.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27468P9A6S | CONN RCPT 6POS JAM NUT W/SCKT |
| MS27484T10F35PC | CONN PLUG 13POS STRAIGHT W/PINS |
| VI-BWT-MY | CONVERTER MOD DC/DC 6.5V 50W |
| MS27484T10F35PB | CONN PLUG 13POS STRAIGHT W/PINS |
| VI-BWR-MY | CONVERTER MOD DC/DC 7.5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7610BSTZ | 功能描述:IC ADC 16BIT 250KSPS 48-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7610BSTZ-RL | 功能描述:IC ADC 16BIT 250KSPS 48-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7611ACP | 制造商:Analog Devices 功能描述:1MSPS, 16-BIT ADC S/W PROG. INPUT RANGES - Bulk |
| AD7611AST | 制造商:Analog Devices 功能描述:1MSPS, 16-BIT ADC S/W PROG. INPUT RANGES - Bulk |
| AD7612 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 1 MSPS, Differential, Programmable Input PulSAR ADC |
发布紧急采购，3分钟左右您将得到回复。