参数资料
| 型号： | AD7628KN |
| 厂商： | Analog Devices Inc |
| 文件页数： | 4/8页 |
| 文件大小： | 0K |
| 描述： | IC DAC 8BIT DUAL MULTIPLY 20-DIP |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 标准包装： | 18 |
| 设置时间： | 400ns |
| 位数： | 8 |
| 转换器数目： | 2 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 450mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 20-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 20-PDIP |
| 包装： | 管件 |
| 输出数目和类型： | 2 电流，单极；2 电流，双极 |
| 采样率（每秒）： | 2.9M |
AD7628
–4–
REV. A
INTERFACE LOGIC INFORMATION
DAC Selection
Both DAC latches share a common 8-bit input port. The con-
trol input
DAC A/DAC B selects which DAC can accept data
from the input port.
Mode Selection
Inputs
CS and WR control the operating mode of the selected
DAC. See Mode Selection Table below.
Write Mode
When
CS and WR are both low, the selected DAC is in the write
mode. The input data latches of the selected DAC are transpar-
ent and its analog output responds to activity on DB0–DB7.
Hold Mode
The selected DAC latch retains the data that was present on
DB0–DB7 just prior to
CS or WR assuming a high state. Both
analog outputs remain at the values corresponding to the data in
their respective latches.
Mode Selection Table
DAC A/
DAC B
CS
WR
DAC A
DAC B
L
WRITE
HOLD
H
L
HOLD
WRITE
X
H
X
HOLD
X
H
HOLD
L = Low State, H = High State, X = Don’t Care
WRITE CYCLE TIMING DIAGRAM
CIRCUIT INFORMATION—D/A SECTION
The AD7628 contains two identical 8-bit multiplying D/A con-
verters, DAC A and DAC B. Each DAC consists of a highly
stable thin film R-2R ladder and eight N-channel current steering
switches. A simplified D/A circuit for DAC A is shown in Figure
1. An inverted R-2R ladder structure is used; that is, binary
Figure 1. Simplified Functional Circuit for DAC A
weighted currents are switched between the DAC output and
AGND, thus maintaining fixed currents in each ladder leg inde-
pendent of switch state.
EQUIVALENT CIRCUIT ANALYSIS
Figure 2 shows an approximate equivalent circuit for one of
the AD7628’s D/A converters, in this case DAC A. A similar
equivalent circuit can be drawn for DAC B. Note that AGND
(Pin 1) is common for both DAC A and DAC B.
The current source ILEAKAGE is composed of surface and junc-
tion leakages and, as with most semiconductor devices, approxi-
mately doubles every 10
°C. The resistor Ro, as shown in Fig-
ure 2, is the equivalent output resistance of the device, which
varies with input code (excluding all 0s code) from 0.8R to 2R.
R is typically 11 k
. C
OUT is the capacitance due to the N-channel
switches and varies from about 50 pF to 120 pF, depending on
the digital input. g(VREF A, N) is the Thevenin equivalent volt-
age generator due to the reference input voltage VREF A and the
transfer function of the R-2R ladder.
For further information on CMOS multiplying D/A converters,
refer to “CMOS DAC Application Guide, 2ND Edition” avail-
able from Analog Devices, Publication Number G872a–15–4/86.
Figure 2. Equivalent Analog Output Circuit of DAC A
CIRCUIT INFORMATION–DIGITAL SECTION
The input buffers are simple CMOS level-shifters designed so
that when the AD7628 is operated with VDD from 10.8 V to
15.75 V, the buffer converts TTL input levels (2.4 V and 0.8 V)
into CMOS logic levels. When VIN is in the region of 1.0 volt to
2.0 volts, the input buffers operate in their linear region and
pass a quiescent current (see Figure 3). To minimize power sup-
ply currents, it is recommended that the digital input voltages be as
close to the supply rails (VDD and DGND) as practicably possible.
The AD7628 may be operated with any supply voltage in the
range 10.8
≤ V
DD
≤ 15.75 volts.
Figure 3. Typical Plot of Supply Current, IDD vs. Logic
Input Voltage VIN to VDD = +15 V
相关PDF资料 |
PDF描述 |
|---|---|
| AD7631BCPZ | IC ADC 18BIT 250KSPS BIP 48LFCSP |
| AD7634BCPZ | IC ADC 18BIT BIPO PROGR 48-LFCSP |
| AD7641BSTZRL | IC ADC 18BIT 2MSPS SAR 48-LQFP |
| AD7643BCPZ | IC ADC 18BIT DIFF W/REF 48LFCSP |
| AD7650ACPZ | IC ADC 16BIT CMOS 5V 48LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7628KNZ | 功能描述:IC DAC 8BIT DUAL MULTIPLY 20-DIP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 设置时间:4µs 位数:12 数据接口:串行 转换器数目:2 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-uMAX 包装:管件 输出数目和类型:2 电压，单极 采样率（每秒）:* 产品目录页面:1398 (CN2011-ZH PDF) |
| AD7628KNZ | 制造商:Analog Devices 功能描述:CMOS DUAL 8 BIT D/A CONVE 制造商:Analog Devices 功能描述:IC, DAC, 8BIT, 2.9MSPS, DIP-20 |
| AD7628KP | 功能描述:IC DAC 8BIT DUAL W/BUFF 20-PLCC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
| AD7628KP/+ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Digital-to-Analog Converter |
| AD7628KP-REEL | 功能描述:IC DAC 8BIT DUAL W/BUFF 20-PLCC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源 功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-DFN-EP（4x3） 包装:管件 输出数目和类型:8 电压，单极 采样率（每秒）:* |
发布紧急采购，3分钟左右您将得到回复。