- 您现在的位置：买卖IC网 > PDF目录10218 > AD7657BSTZ-1-RL (Analog Devices Inc)IC ADC 14BIT 6CH 250KSPS 64LQFP PDF资料下载
参数资料
| 型号： | AD7657BSTZ-1-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 4/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 6CH 250KSPS 64LQFP |
| 标准包装： | 1,500 |
| 位数： | 14 |
| 采样率（每秒）： | 250k |
| 数据接口： | 串行，并联 |
| 转换器数目： | 6 |
| 功率耗散（最大）： | 143mW |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 6 个单端，双极 |
| 配用： | EVAL-AD7657-1EDZ-ND - BOARD EVAL CONTROL AD7657-1 EVAL-AD7657CBZ-ND - BOARD EVAL FOR AD7657 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD7656-1/AD7657-1/AD7658-1
Data Sheet
Rev. D | Page 12 of 32
Pin No.
Mnemonic
Description
19
CS
Chip Select. This active low logic input frames the data transfer. If both CS and RD are logic low and
the parallel interface is selected, the output bus is enabled and the conversion result is output on
the parallel data bus lines. If both CS and WR are logic low and the parallel interface is selected, DB[15:8]
are used to write data to the on-chip control register. When the serial interface is selected, the CS is
used to frame the serial read transfer and clock out the MSB of the serial output data.
20
RD
Read Data. If both CS and RD are logic low and the parallel interface is selected, the output bus is
enabled. When the serial interface is selected, the RD line should be held low.
63
WR/REFEN/DIS
Write Data/Reference Enable and Disable. When the H/S SEL pin is high and both CS and WR are
logic low, DB[15:8] are used to write data to the internal control register. When the H/S SEL pin is
low, this pin is used to enable or disable the internal reference. When H/S SEL = 0 and REFEN/DIS = 0, the
internal reference is disabled and an external reference should be applied to the REFIN/REFOUT pin.
When H/S SEL = 0 and REFEN/
DIS = 1, the internal reference is enabled and the REFIN/REFOUT pin
should be decoupled. See the Internal/External Reference section.
18
BUSY
Busy Output. This pin transitions to high when a conversion is started and remains high until the
conversion is complete and the conversion data is latched into the output data registers. A new
conversion cannot be initiated on the AD7656-1/AD7657-1/AD7658-1 when the BUSY signal is high
because any applied CONVST edges are ignored.
51
REFIN/REFOUT
Reference Input/Reference Output. The on-chip reference is available via this pin. Alternatively, the
internal reference can be disabled and an external reference can be applied to this input. See the
Internal/External Reference section. When the internal reference is enabled, decouple this pin using
at least a 1 F decoupling capacitor.
61
SER/PAR SEL
Serial/Parallel Selection Input. When this pin is low, the parallel interface is selected. When this pin is high,
the serial interface is selected. When the serial interface is selected, DB[10:8] function as DOUT[C:A],
DB[0:2] function as DOUT, and DB7 functions as DCEN. When the serial interface is selected, tie DB15 and
DB[13:11] to DGND.
17
DB0/SEL A
Data Bit 0/Select DOUT A. When SER/PAR SEL = 0, this pin acts as a three-state parallel digital output
pin. When SER/PAR SEL = 1, this pin functions as SEL A and is used to configure the serial interface. If
this pin is 1, the serial interface operates with one, two, or three DOUT output pins and enables
DOUT A as a serial output. When the serial interface is selected, always set this pin to 1.
16
DB1/SEL B
Data Bit 1/Select DOUT B. When SER/PAR SEL = 0, this pin acts as a three-state parallel digital output
pin. When SER/PAR SEL = 1, this pin functions as SEL B and is used to configure the serial interface. If
this pin is 1, the serial interface operates with two or three DOUT output pins and enables DOUT B
as a serial output. If this pin is 0, the DOUT B is not enabled to operate as a serial data output pin
and only one DOUT output pin, DOUT A, is used. Unused serial DOUT pins should be left unconnected.
15
DB2/SEL C
Data Bit 2/Select DOUT C. When SER/PAR SEL = 0, this pin acts as a three-state parallel digital output
pin. When SER/PAR SEL = 1, this pin functions as SEL C and is used to configure the serial interface. If
this pin is 1, the serial interface operates with three DOUT output pins and enables DOUT C as a
serial output. If this pin is 0, the DOUT C is not enabled to operate as a serial data output pin.
Unused serial DOUT pins should be left unconnected.
14
DB3/DCIN C
Data Bit 3/Daisy-Chain Input C. When SER/PAR SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR SEL = 1 and DCEN = 1, this pin acts as Daisy-Chain Input C. When the serial
interface is selected but the device is not used in daisy-chain mode, tie this pin to DGND.
13
DB4/DCIN B
Data Bit 4/Daisy-Chain Input B. When SER/PAR SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR SEL = 1 and DCEN = 1, this pin acts as Daisy-Chain Input B. When the serial
interface is selected but the device is not used in daisy-chain mode, tie this pin to DGND.
12
DB5/DCIN A
Data Bit 5/Daisy-Chain Input A. When SER/PAR SEL is low, this pin acts as a three-state parallel digital
output pin. When SER/PAR SEL = 1 and DCEN = 1, this pin acts as Daisy-Chain Input A. When the serial
interface is selected but the device is not used in daisy-chain mode, tie this pin to DGND.
11
DB6/SCLK
Data Bit 6/Serial Clock. When SER/PAR SEL = 0, this pin acts as a three-state parallel digital output pin.
When SER/PAR SEL = 1, this pin functions as SCLK input and is the read serial clock for the serial transfer.
10
DB7/HBEN/DCEN
Data Bit 7/High Byte Enable/Daisy-Chain Enable. When the parallel interface is selected and the device is
used in word mode (SER/PAR SEL = 0 and W/B = 0), this pin functions as Data Bit 7. When the parallel
interface is selected and the device is used in byte mode (SER/PAR SEL = 0 and W/B = 1), this pin
functions as HBEN. If the HBEN pin is logic high, the data is output MSB byte first on DB[15:8]. If the
HBEN pin is logic low, the data is output LSB byte first on DB[15:8]. When the serial interface is
selected (SER/PAR SEL = 1), this pin functions as DCEN. If the DCEN pin is logic high, the parts
operate in daisy-chain mode with DB[5:3] functioning as DCIN[A:C]. When the serial interface is
selected but the device is not used in daisy-chain mode, this pin should be tied to DGND.
相关PDF资料 |
PDF描述 |
|---|---|
| SP3222EBCT-L/TR | IC TXRX RS232 ESD TRUE 18WSOIC |
| ADAU1461WBCPZ-RL | IC SIGMADSP 24BIT 96KHZ PLL 32 |
| SP3222EBCA-L/TR | IC TXRX RS232 ESD TRUE 20SSOP |
| AD7657BSTZ-REEL | IC ADC 14BIT 6CH 250KSPS 64-LQFP |
| LTC1867AIGN | IC ADC 16BIT 8CH 200KSPS 16SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7657BSTZ-REEL | 功能描述:IC ADC 14BIT 6CH 250KSPS 64-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7657YSTZ | 功能描述:IC ADC 14BIT 6CH 250KSPS 64LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7657YSTZ-1 | 功能描述:IC ADC 14BIT 6CH 250KSPS 64LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7657YSTZ-1-RL | 功能描述:IC ADC 14BIT 6CH 250KSPS 64LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7657YSTZ-REEL | 功能描述:IC ADC 14BIT 6CH 250KSPS 64LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。