- 您现在的位置：买卖IC网 > PDF目录10280 > AD7682BCPZRL7 (Analog Devices Inc)IC ADC 16BIT 4CH 250KSPS 20LFCSP PDF资料下载
参数资料
| 型号： | AD7682BCPZRL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 22/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 4CH 250KSPS 20LFCSP |
| 产品培训模块： | Power Line Monitoring |
| 产品变化通告： | Startup Circuitry Design Improvement Change 15/April/2009 |
| 标准包装： | 1,500 |
| 系列： | PulSAR® |
| 位数： | 16 |
| 采样率（每秒）： | 250k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 21mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 20-LFCSP-VQ |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 8 个单端，单极；4 个差分，双极；4 个伪差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Data Sheet
AD7682/AD7689
Rev. D | Page 29 of 32
READ/WRITE SPANNING CONVERSION WITHOUT
A BUSY INDICATOR
to any host using an SPI, serial port, or FPGA. The connection
diagram is shown in Figure 40, and the corresponding timing
is given in Figure 41. For the SPI, the host should use CPHA =
CPOL = 0. Reading/writing spanning conversion is shown,
which covers all three modes detailed in the Digital Interface
section. For this mode, the host must generate the data transfer
based on the conversion time. For an interrupt driven transfer
that uses a busy indicator, refer to the Read/Write Spanning
Conversion with a Busy Indicator section.
A rising edge on CNV initiates a conversion, forces SDO to
high impedance, and ignores data present on DIN. After a
conversion is initiated, it continues until completion irrespec-
tive of the state of CNV. CNV must be returned high before the
safe data transfer time, tDATA, and then held high beyond the
conversion time, tCONV, to avoid generation of the busy signal
indicator.
the acquisition phase and power-down. When the host brings
CNV low after tCONV (maximum), the MSB is enabled on SDO.
The host also must enable the MSB of the CFG register at this
time (if necessary) to begin the CFG update. While CNV is low,
both a CFG update and a data readback take place. The first 14
SCK rising edges are used to update the CFG, and the first 15
SCK falling edges clock out the conversion results starting with
MSB 1. The restriction for both configuring and reading is
that they both must occur before the tDATA time of the next conver-
sion elapses. All 14 bits of CFG[13:0] must be written, or they
are ignored. In addition, if the 16-bit conversion result is not
read back before tDATA elapses, it is lost.
The SDO data is valid on both SCK edges. Although the rising
edge can be used to capture the data, a digital host using the
SCK falling edge allows a faster reading rate, provided it has an
acceptable hold time. After the 16th (or 30th) SCK falling edge, or
when CNV goes high (whichever occurs first), SDO returns to
high impedance.
If CFG readback is enabled, the CFG register associated with the
conversion result is read back MSB first following the LSB of the
conversion result. A total of 30 SCK falling edges is required to
return SDO to high impedance if this is enabled.
MISO
MOSI
SCK
SS
CNV
FOR SPI USE CPHA = 0, CPOL = 0.
SCK
SDO
DIN
AD7682/
AD7689
DIGITAL HOST
07
35
3-
03
6
UPDATE (n)
CFG/SDO
UPDATE (n + 1)
CFG/SDO
ACQUISITION (n)
ACQUISITION
(n + 1)
ACQUISITION
(n - 1)
MSB MSB – 1
1
2
BEGIN DATA (n – 1)
BEGIN CFG (n + 1)
CFG
MSB
CFG
MSB – 1
LSB + 1
14
15
SEE NOTE
NOTES
1. THE LSB IS FOR CONVERSION RESULTS OR THE CONFIGURATION REGISTER CFG (n – 1) IF
15 SCK FALLING EDGES = LSB OF CONVERSION RESULTS.
29 SCK FALLING EDGES = LSB OF CONFIGURATION REGISTER.
ON THE 16TH OR 30TH SCK FALLING EDGE, SDO IS DRIVEN TO HIGH IMPENDANCE.
16/
30
CONVERSION (n)
END DATA (n – 1)
END CFG (n + 1)
CFG
LSB
X
>
tCONV
LSB
SCK
CNV
DIN
SDO
LSB + 1
14
15
16/
30
CONVERSION (n – 1)
END DATA (n – 2)
END CFG (n)
CFG
LSB
X
tCONV
tDATA
tCNVH
tDATA
tDIS
tEN
tDSDO
tHSDO
tHDIN
tSDIN
tCLSCK
tEN
tSCK
tSCKH
tSCKL
tDIS
tCONV
LSB
07
35
3-
0
37
tACQ
tCYC
(QUIET
TIME)
(QUIET
TIME)
EOC
RETURN CNV HIGH
FOR NO BUSY
RETURN CNV HIGH
FOR NO BUSY
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/26FJ20AN | CONN HSG PLUG 30POS STRGHT PINS |
| R4MZ | CONN PLUG CORD 4POS MALE R/A |
| CS5361-KSZR | IC ADC AUD 114DB 204KHZ 24-SOIC |
| D38999/20MJ43BN | CONN HSG RCPT 43POS WALL MT SCKT |
| VE-BN2-MY | CONVERTER MOD DC/DC 15V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7683 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 100 kSPS PulSAR ADC in MSOP/QFN |
| AD7683ACPZRL | 功能描述:IC ADC 16BIT SRL 100KSPS 8LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7683ACPZRL7 | 功能描述:IC ADC 16BIT 100KSPS 8LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7683ARM | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 16-bit Serial 8-Pin MSOP Tube |
| AD7683ARMRL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 16-bit Serial 8-Pin MSOP T/R |
发布紧急采购，3分钟左右您将得到回复。