- 您现在的位置：买卖IC网 > PDF目录10663 > AD7686BRMZ (Analog Devices Inc)IC ADC 16BIT 500KSPS 10-MSOP PDF资料下载
参数资料
| 型号： | AD7686BRMZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 500KSPS 10-MSOP |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| 位数： | 16 |
| 采样率（每秒）： | 500k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 21.5mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个伪差分，单极 |
| 产品目录页面： | 778 (CN2011-ZH PDF) |
| 配用： | EVAL-AD7686CBZ-ND - BOARD EVALUATION FOR AD7686 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7686
Rev. B | Page 20 of 28
CS MODE 4-WIRE WITH BUSY INDICATOR
This mode is usually used when a single AD7686 is connected
to an SPI-compatible digital host, which has an interrupt input,
and when it is desired to keep CNV, which is used to sample the
analog input, independent of the signal used to select the data
reading. This requirement is particularly important in applications
where low jitter on CNV is desired. The connection diagram is
shown in Figure 39, and the corresponding timing is provided
in Figure 40.
With SDI high, a rising edge on CNV initiates a conversion,
selects the CS mode, and forces SDO to high impedance. In this
mode, CNV must be held high during the conversion phase and
the subsequent data readback (if SDI and CNV are low, SDO is
driven low). Prior to the minimum conversion time, SDI can be
used to select other SPI devices, such as analog multiplexers,
but SDI must be returned low before the minimum conversion
time and held low until the maximum conversion time to
guarantee the generation of the busy signal indicator. When
conversion is complete, SDO goes from high impedance to low.
With a pull-up on the SDO line, this transition can be used as
an interrupt signal to initiate the data readback controlled by
the digital host. The AD7686 then enters the acquisition phase
and powers down. The data bits are then clocked out, MSB first,
by subsequent SCK falling edges. The data is valid on both SCK
edges. Although the rising edge can be used to capture the data,
a digital host using the SCK falling edge allows a faster reading
rate, provided it has an acceptable hold time. After the optional
17th SCK falling edge or SDI going high, whichever occurs first,
the SDO returns to high impedance.
DATA IN
IRQ
CLK
CONVERT
CS1
VIO
DIGITAL HOST
02
96
9-
04
0
47k
CNV
SCK
SDO
SDI
AD7686
Figure 39. CS Mode 4-Wire with Busy Indicator Connection Diagram
SDO
D15
D14
D1
D0
tDIS
SCK
1
2
3
151617
tSCK
tSCKL
tSCKH
tHSDO
tDSDO
tEN
CONVERSION
ACQUISITION
tCONV
tCYC
tACQ
ACQUISITION
SDI
CNV
tSSDICNV
tHSDICNV
02
96
9-
0
41
Figure 40. CS Mode 4-Wire with Busy Indicator Serial Interface Timing
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9141ESA+T | IC COMPARATOR R-R 8-SOIC |
| AD7663ASTZ | IC ADC 16BIT CMOS 48-LQFP |
| VI-21N-MX | CONVERTER MOD DC/DC 18.5V 75W |
| AD9243ASZ | IC ADC 14BIT 3MSPS 44-MQFP |
| AD7893ANZ-2 | IC ADC 12BIT SRL T/H LP 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7686BRMZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 500 kSPS PulSAR ADC in MSOP/QFN |
| AD7686BRMZRL7 | 功能描述:IC ADC 16BIT 500KSPS 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7686BRMZRL71 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 500 kSPS PulSAR ADC in MSOP/QFN |
| AD7686CB2 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 500 kSPS PulSAR ADC in MSOP/QFN |
| AD7686CBZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 500 kSPS PulSAR ADC in MSOP/QFN |
发布紧急采购，3分钟左右您将得到回复。