- 您现在的位置：买卖IC网 > PDF目录378276 > AD7739BRU-REEL7 (ANALOG DEVICES INC) 8-Channel, High Throughput, 24-Bit Sigma-Delta ADC PDF资料下载
参数资料
| 型号： | AD7739BRU-REEL7 |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | ADC |
| 英文描述： | 8-Channel, High Throughput, 24-Bit Sigma-Delta ADC |
| 中文描述： | 8-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO24 |
| 封装： | MS-153AD, TSSOP-24 |
| 文件页数： | 30/32页 |
| 文件大小： | 380K |
| 代理商： | AD7739BRU-REEL7 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页
AD7739
CALIBRATION
The AD7739 provides zero-scale self-calibration, and zero- and
full-scale system calibration capability that can effectively
reduce the offset error and gain error to the order of the noise.
After each conversion, the ADC conversion result is scaled
using the ADC calibration registers and the relevant channel
calibration registers before being written to the data register.
Rev. 0 | Page 30 of 32
For unipolar ranges:
Data = ((ADC result – R × ADC ZS Cal. reg.)
× ADC FS reg./(0x20 0000) – R × Ch. ZS Cal. reg.)
× Ch. FS Cal. reg./(0x20 0000)
For bipolar ranges:
Data = ((ADC result – R × ADC ZS Cal. reg.)
× ADC FS reg./(0x40 0000) + (0x80 0000) – R × Ch. ZS Cal. reg.)
× Ch. FS Cal. reg./(0x20 0000)
where the ADC result is in the range of 0 to 0xFF FFFF.
R = 1 for input ranges +1.25 V, ±1.25 V, +2.5 V, and ±2.5 V
R = 2 for input ranges +0.625 V, and ±0.625 V
Note that the channel zero-scale calibration register has the
format of a sign bit and a 22-bit channel offset value.
To start any calibration, write the relevant mode bits to the
AD7739 mode register. After the calibration is complete, the
contents of the corresponding calibration registers are updated,
all RDY bits in the ADC status register are set, the SYNC pin
goes low, and the AD7739 reverts to idle mode. The calibration
duration is the same as the conversion time configured on the
selected channel. A longer conversion time gives less noise and
yields a more exact calibration; therefore, use at least the default
conversion time to initiate any calibration.
ADC Zero-Scale Self-Calibration
The ADC zero-scale self-calibration can reduce the ADC offset
error in the chopping disabled mode. If repeated after a
temperature change, it can also reduce the offset drift error in
the chopping disabled mode.
The zero-scale self-calibration is performed on internally
shorted ADC inputs. The negative analog input terminal on the
selected channel is used to set the ADC zero-scale calibration
common mode. Therefore, either the negative terminal of the
selected differential pair or the AINCOM on the single-ended
channel configuration should be driven to a proper common-
mode voltage.
It is recommended that the ADC zero-scale calibration register
be updated only as part of an ADC zero-scale self-calibration.
ADC Full-Scale Self-Calibration
The ADC full-scale self-calibration can reduce the ADC full-
scale error for the +2.5 V and ±2.5 V input range. If repeated
after a temperature change, it can also reduce the full-scale drift.
The ADC full-scale self-calibration is performed with a +2.5 V
input voltage range on internally generated full-scale voltage
(V
REF
), regardless of the input voltage range set in the channel
setup register. Full-scale errors in the ±1.25 V, +1.25 V, ±0.625 V,
and +0.625 V ranges are not calibrated as this would require an
accurate low voltage source other than the reference.
If the 1.25 V or 0.625 V ranges are used on any channel, the
ADC full-scale self-calibration is not recommended. A system
full-scale calibration should be performed if accurate gains
need to be achieved on these ranges.
It is recommended that the ADC full-scale calibration register
be updated only as part of an ADC full-scale self-calibration for
the +2.5 V and ±2.5 V input range.
Per Channel System Calibration
The per channel system calibration can reduce the system offset
error and the system gain error. If repeated after a temperature
change, it can also reduce the system offset and gain drifts.
If the per channel system calibrations are used, these should be
initiated in the following order: a channel zero-scale system
calibration, followed by a channel full-scale system calibration.
The system calibration is affected by the ADC zero-scale and
full-scale calibration registers. Therefore, if both self-calibration
and system calibration are used in the system, an ADC self-
calibration should be performed first, followed by a system
calibration cycle.
The voltage range in the channel setup register should be set
before executing the channel system calibration.
While executing a system calibration, the fully settled system
zero-scale voltage signal or system full-scale voltage signal must
be connected to the selected channel analog inputs.
The per channel calibration registers can be read, stored, or
modified and written back to the AD7739. Note that when
writing the calibration registers, the AD7739 must be in idle
mode. Note that outside the specified calibration range,
calibration is possible, but the performance may degrade
(see the System Calibration section in Table 1).
相关PDF资料 |
PDF描述 |
|---|---|
| AD79024 | LC2MOS 20-Bit Data Acquisition System |
| AD8152 | 34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch |
| AD8152-EVAL | 34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch |
| AD8152JBP | 34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch |
| AD82550A | Stereo Digital Audio Amplifier with Headphone Driver |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7739BRUZ | 功能描述:IC ADC 24BIT 8-CH 24-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7739BRUZ | 制造商:Analog Devices 功能描述:IC, ADC, 24BIT, 15.1KSPS, TSSOP-24 |
| AD7739BRUZ-REEL7 | 功能描述:IC ADC 24BIT 8CH SIG-DEL 24TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD773A | 制造商:AD 制造商全称:Analog Devices 功能描述:10-Bit, 20 MSPS Monolithic A/D Converter |
| AD773AJD | 制造商:Analog Devices 功能描述:ADC Single Pipelined 20Msps 10-bit Parallel 28-Pin CDIP 制造商:Rochester Electronics LLC 功能描述:IC, 10-BIT 20 MSPS ADC - Bulk |
发布紧急采购，3分钟左右您将得到回复。