参数资料
| 型号： | AD7747ARUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | IC CONV 24BIT CAP-DGTL 16-TSSOP |
| 标准包装： | 96 |
| 类型： | 电容数字转换器 |
| 分辨率（位）： | 24 b |
| 数据接口： | 串行 |
| 电压电源： | 单电源 |
| 电源电压： | 2.7 V ~ 5.25 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 781 (CN2011-ZH PDF) |
| 配用： | EVAL-AD7747EBZ-ND - BOARD EVAL FOR AD7747 |
| 其它名称： | Q23139198 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7747
Rev. 0 | Page 23 of 28
CAPDIFF = 1
±8pF
CDC
CAPDAC(+)
17pF
CAPDAC(–)
17pF
05
46
9-
0
21
CY
17pF
SHLD
CIN(+)
CIN(–)
0x000000
TO
0xFFFFFF
DATA
CX
9 TO 25pF
(17pF ± 8pF)
Figure 32. Using CAPDAC in Differential Configuration
PARASITIC CAPACITANCE
The CDC architecture used in the AD7747 measures the
capacitance CX connected between the CIN pin and ground.
Most applications use the active shield to avoid external influ-
ences during the CDC. However, any parasitic capacitance, CP,
as shown in Figure 33, can affect the CDC result.
DATA
CDC
SHLD
CIN
CX
CP1
CP2
CP3
05
46
9-
0
41
Figure 33. Parasitic Capacitance
A parasitic capacitance, CP1, coupled in between CIN and
ground adds directly to the value of the capacitance CX and,
therefore, the CDC result is: DATA ≈ CX + CP1. An offset cali-
bration might be sufficient to compensate for a small parasitic
capacitance (CP1 ≤ 1pF). For a larger parasitic capacitance, the
CAPDAC can be used to compensate, followed by an offset
calibration to ensure the full range of ±8pF is available for
the system.
Other parasitic capacitances, such as CP2 between active shield
and ground as well as CP3 between the CIN pin and SHLD,
could influence the conversion result. However, the graphs in
the Typical Performance Characteristics section show that the
effect of parasitic capacitance of type CP2/CP3 below 250 pF is
by CP3.
PARASITIC RESISTANCE
DATA
CDC
SHLD
CIN
CX
RP1
RP3
RP2
05
64
9-
0
42
Figure 34. Parasitic Resistance on CIN
Parasitic resistances, as shown in Figure 34, cause leakage
currents, which affect the CDC result. The AD7747 CDC
measures the charge transfer between the CIN pin and ground.
Any resistance connected in parallel to the measured
capacitance, CX, such as the parasitic resistance, RP1, also
transfers charge. Therefore, the parallel resistor is seen as an
additional capacitance in the output data. A resistance in the
range of RP1 ≥ 10 MΩ causes an offset error in the CDC result.
An offset calibration can be used to compensate for the effect of
small leakage currents. A higher leakage current to ground,
RP1 ≤ 10 MΩ, results in a gain error, an offset error, and a
nonlinearity error. See Figure 10 in the Typical Performance
Characteristics section.
A parasitic resistance, R P2, between SHLD and ground, as well
as RP3 between the CIN pin and the active shield, as shown in
Figure 34, cause a leakage current, which affects the CDC result
and is seen as an offset in the data. An offset calibration can be
used to compensate for effect of the small leakage current
Characteristics section.
PARASITIC SERIAL RESISTANCE
DATA
CDC
SHLD
CIN
CX
RS
0
54
69
-04
3
Figure 35. Parasitic Serial Resistance
The AD7747 CDC result is affected by a resistance in series
with the measured capacitance. The serial resistance should be
less than 10 kΩ for the specified performance. See Figure 14 in
the Typical Performance Characteristics section.
CAPACITIVE GAIN CALIBRATION
The AD7747 gain is factory calibrated for the full scale of
±8.192 pF in the production for each part individually. The
factory gain coefficient is stored in a one-time programmable
(OTP) memory and is copied to the capacitive gain register at
power-up or after reset.
The gain can be changed by executing a capacitance gain calibra-
tion mode, for which an external full-scale capacitance needs
to be connected to the capacitance input, or by writing a user
value to the capacitive gain register. This change would be only
temporary, and the factory gain coefficient would be reloaded
back after power-up or reset. The part is tested and specified for
use only with the default factory calibration coefficient.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27474E8B35P | CONN RCPT 6POS JAM NUT W/PINS |
| AD7745ARUZ | IC CONV 1CH CAP TO DGTL 16TSSOP |
| VI-B12-IU-S | CONVERTER MOD DC/DC 15V 200W |
| VE-B12-IU-S | CONVERTER MOD DC/DC 15V 200W |
| AD9823KRUZ | IC CDS FOR DGTL CAMERA 14-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7747ARUZ-REEL | 功能描述:IC CONV CAP TO DIG 24BIT 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| AD7747ARUZ-REEL7 | 功能描述:IC CONV CAP TO DIG 24BIT 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| AD7748BSTZ | 制造商:Analog Devices 功能描述: |
| AD774B | 制造商:AD 制造商全称:Analog Devices 功能描述:Complete 12-Bit A/D Converters |
发布紧急采购，3分钟左右您将得到回复。