- 您现在的位置：买卖IC网 > PDF目录10279 > AD7766BRUZ-1-RL7 (Analog Devices Inc)IC ADC 24BIT 64KSPS SAR 16TSSOP PDF资料下载
参数资料
| 型号： | AD7766BRUZ-1-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/25页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT 64KSPS SAR 16TSSOP |
| 标准包装： | 1,000 |
| 位数： | 24 |
| 采样率（每秒）： | 64k |
| 数据接口： | 串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 18mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个差分，单极 |
| 配用： | EVAL-AD7766EDZ-ND - BOARD EVAL AD7766 128KSPS 108DB EVAL-AD7766-2EDZ-ND - BOARD EVAL AD7766-2 32KSPS 114DB EVAL-AD7766-1EDZ-ND - BOARD EVAL AD7766-1 64KSPS 111DB |
AD7766
Rev. C | Page 14 of 24
TERMINOLOGY
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the actual input signal’s rms value to the rms
sum of all other spectral components below the Nyquist frequency,
excluding harmonics and dc. The value for SNR is expressed in
decibels.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of harmonics to the fundamen-
tal. For the AD7766, it is defined as
()
1
6
5
4
3
2
V
THD
2
log
20
dB
+
=
where:
V1
is the rms amplitude of the fundamental.
V2, V3, V4, V5,
and V6 are the rms amplitudes of the second to
the sixth harmonics.
Nonharmonic Spurious-Free Dynamic Range (SFDR)
SFDR is the ratio of the rms signal amplitude to the rms value
of the peak spurious spectral component, excluding harmonics.
Dynamic Range
Dynamic range is the ratio of the rms value of the full scale to
the rms noise measured with the inputs shorted together. The
value for the dynamic range is expressed in decibels.
Intermodulation Distortion (IMD)
With inputs consisting of sine waves at two frequencies, fa
and fb, any active device with nonlinearities creates distortion
products at sum and difference frequencies of mfa ± nfb, where
m, n = 0, 1, 2, 3, and so on. Intermodulation distortion terms
are those for which neither m nor n is equal to 0. For example,
the second-order terms include (fa + fb) and (fa fb), and the
third-order terms include (2fa + fb), (2fa fb), (fa + 2fb), and
(fa 2fb).
The AD7766 is tested using the CCIF standard, where two input
frequencies near the top end of the input bandwidth are used.
In this case, the second-order terms are usually distanced in
frequency from the original sine waves, and the third-order
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
as per the THD specification, where it is the ratio of the rms
sum of the individual distortion products to the rms amplitude
of the sum of the fundamentals expressed in decibels.
Integral Nonlinearity (INL)
INL is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function.
Differential Nonlinearity (DNL)
DNL is the difference between the measured and the ideal
1 LSB change between any two adjacent codes in the ADC.
Zero Error
Zero error is the difference between the ideal midscale input
voltage (when both inputs are shorted together) and the actual
voltage producing the midscale output code.
Zero Error Drift
Zero error drift is the change in the actual zero error value due
to a temperature change of 1°C. It is expressed as a percentage
of full scale at room temperature.
Gain Error
The first transition (from 100 … 000 to 100 … 001) should occur
LSB above the nominal negative full scale for an analog voltage.
The last transition (from 011 … 110 to 011 … 111) should occur
1 LSB below the nominal full scale for an analog voltage. The
gain error is the deviation of the difference between the actual
level of the last transition and the actual level of the first transition,
from the difference between the ideal levels.
Gain Error Drift
Gain error drift is the change in the actual gain error value due
to a temperature change of 1°C. It is expressed as a percentage
of full scale at room temperature.
Common-Mode Rejection Ratio (CMRR)
CMRR is defined as the ratio of the power in the ADC output
at full-scale frequency f to the power of a 100 mV sine wave
applied to the common-mode voltage of the VIN+ and VIN
inputs at frequency fS.
CMRR
(dB) = 10 log(Pf/PfS)
where Pf is the power at the frequency f in the ADC output, and
PfS
is the power at the frequency fS in the ADC output.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27497T24B4SLC | CONN HSG RCPT 56POS WALL MT SCKT |
| VE-JN4-MX-S | CONVERTER MOD DC/DC 48V 75W |
| MS27505E15B15PA | CONN RCPT 15POS BOX MNT W/PINS |
| D38999/20MG11BN | CONN HSG RCPT 11POS WALL MT SCKT |
| VE-JN3-MX-S | CONVERTER MOD DC/DC 24V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7766BRUZ-2 | 功能描述:IC ADC 24BIT 32KSPS SAR 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7766BRUZ-2-RL7 | 功能描述:IC ADC 24BIT 32KSPS SAR 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7766BRUZ-RL7 | 功能描述:IC ADC 24BIT 128KSPS SAR 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7767 | 制造商:AD 制造商全称:Analog Devices 功能描述:24-Bit, 8.5 mW, 109 dB, 128/64/32 kSPS ADCs |
| AD7767BRUZ | 功能描述:ADC 24BIT 128KSPS SAR 16-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
发布紧急采购，3分钟左右您将得到回复。