- 您现在的位置：买卖IC网 > PDF目录10325 > AD7789BRM-REEL (Analog Devices Inc)IC ADC 24BIT SIGMA-DELTA 10-MSOP PDF资料下载
参数资料
| 型号： | AD7789BRM-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/20页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT SIGMA-DELTA 10-MSOP |
| 标准包装： | 3,000 |
| 位数： | 24 |
| 采样率（每秒）： | 16.6 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 230µW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个差分，单极；1 个差分，双极 |
AD7788/AD7789
Rev. B | Page 11 of 20
ON-CHIP REGISTERS
The ADC is controlled and configured via a number of on-chip
registers, which are described on the following pages. In the
following descriptions, set implies a Logic 1 state and cleared
implies a Logic 0 state, unless otherwise stated.
COMMUNICATIONS REGISTER
(RS1, RS0 = 0, 0)
The communications register is an 8-bit, write only register. All
communications to the part must start with a write operation to
the communications register. The data written to the commun-
ications register determines whether the next operation is a read
or write operation, and to which register this operation takes
place.
For read or write operations, once the subsequent read or write
operation to the selected register is complete, the interface returns
to where it expects a write operation to the communications
register. This is the default state of the interface and, on power-up
or after a reset, the ADC is in this default state waiting for a write
operation to the communications register. In situations where the
interface sequence is lost, a write operation of at least 32 serial
clock cycles with DIN high returns the ADC to this default state
by resetting the entire part. Table 7 outlines the bit designations
for the communications register. CR0 through CR7 indicate the
bit location, CR denoting the bits are in the communications
register. CR7 denotes the first bit of the data stream. The number
in brackets indicates the power-on/reset default status of that bit.
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
WEN[0]
0[0]
RS1[0]
RS0[0]
R/W[0]
CREAD[0]
CH1[0]
CH0[0]
Table 7. Communications Register Bit Designations
Bit Location
Bit Name
Description
CR7
WEN
Write Enable Bit. A 0 must be written to this bit so that the write to the communications register actually
occurs. If a 1 is the first bit written, the part does not clock on to subsequent bits in the register. It stays at
this bit location until a 0 is written to this bit. Once a 0 is written to the WEN bit, the next seven bits are
loaded to the communications register.
CR6
0
This bit must be programmed with a Logic 0 for correct operation.
CR5 to CR4
RS1 to RS0
Register Address Bits. These address bits are used to select which of the ADC registers are being selected
during this serial interface communication (see Table 8).
CR3
R/W
A 0 in this bit location indicates that the next operation is a write to a specified register. A 1 in this position
indicates that the next operation is a read from the designated register.
CR2
CREAD
Continuous Read of the Data Register. When this bit is set to 1 (and the data register is selected), the serial
interface is configured so that the data register can be continuously read, that is, the contents of the data
register are placed on the DOUT/RDY pin automatically when the SCLK pulses are applied. The
communications register does not have to be written to for data reads. To enable continuous read mode,
the instruction 001111XX must be written to the communications register. To exit the continuous read
mode, the instruction 001110XX must be written to the communications register while the DOUT/RDY pin
is low. While in continuous read mode, the ADC monitors activity on the DIN line so that it can receive the
instruction to exit continuous read mode. Additionally, a reset occurs if 32 consecutive 1s are seen on DIN.
Therefore, DIN should be held low in continuous read mode until an instruction is to be written to the
device.
CR1 to CR0
CH1 to CH0
These bits are used to select the analog input channel. The differential channel can be selected
AIN(+)/AIN(
) or an internal short AIN()/AIN() can be selected. Alternatively, the power supply can be
selected, that is, the ADC can measure the voltage on the power supply, which is useful for monitoring
power supply variation. The power supply voltage is divided by 5 and then applied to the modulator for
conversion. The ADC uses a 1.17 V ± 5% on-chip reference as the reference source for the analog-to-digital
conversion. Any change in channel resets the filter and a new conversion is started.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9288BSTZRL-40 | IC ADC 8BIT DUAL 40MSPS 48LQFP |
| VE-24D-IU-S | CONVERTER MOD DC/DC 85V 200W |
| VI-B2X-MW-S | CONVERTER MOD DC/DC 5.2V 100W |
| LTC2499CUHF#TRPBF | IC ADC 24BIT DELTA SIG 38-QFN |
| AD7887ARZ-REEL7 | IC ADC 12BIT 2CHAN SRL 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7789BRMZ | 功能描述:IC ADC 24BIT LP 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7789BRMZ-REEL | 功能描述:IC ADC 24BIT SIGMA-DELTA 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD779 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit 128 kSPS Complete Sampling ADC |
| AD7790 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, 16-Bit Buffered Sigma-Delta ADC |
| AD779-05A6 | 制造商: 功能描述: 制造商:undefined 功能描述: |
发布紧急采购，3分钟左右您将得到回复。