- 您现在的位置：买卖IC网 > PDF目录10269 > AD7794CRUZ-REEL (Analog Devices Inc)IC ADC 24BIT 6CH LP 24-TSSOP PDF资料下载
参数资料
| 型号： | AD7794CRUZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/37页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT 6CH LP 24-TSSOP |
| 产品培训模块： | ADC Applications ADC Architectures ADC DC/AC Performance |
| 标准包装： | 2,500 |
| 位数： | 24 |
| 采样率（每秒）： | 470 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 2.5mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 6 个差分，单极；6 个差分，双极 |
| 配用： | EVAL-AD7794EBZ-ND - BOARD EVALUATION FOR AD7794 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
AD7794/AD7795
Rev. D | Page 20 of 36
Table 18. Operating Modes
MD2
MD1
MD0
Mode
0
Continuous Conversion Mode (Default).
In continuous conversion mode, the ADC continuously performs conversions and places the result in the data
register. RDY goes low when a conversion is complete. The user can read these conversions by placing the device
in continuous read mode whereby the conversions are automatically placed on the DOUT line when SCLK pulses
are applied. Alternatively, the user can instruct the ADC to output the conversion by writing to the communica-
tions register. After power-on, the first conversion is available after a period of 2/fADC when chop is enabled or
1/fADC when chop is disabled. Subsequent conversions are available at a frequency of fADC with chop either
enabled or disabled.
0
1
Single Conversion Mode.
When single conversion mode is selected, the ADC powers up and performs a single conversion. The oscillator
requires 1 ms to power up and settle. The ADC then performs the conversion, which takes a time of 2/fADC when
chop is enabled, or 1/fADC when chop is disabled. The conversion result is placed in the data register, RDY goes
low, and the ADC returns to power-down mode. The conversion remains in the data register and RDY remains
active (low) until the data is read or another conversion is performed.
0
1
0
Idle Mode.
In idle mode, the ADC filter and modulator are held in a reset state although the modulator clocks are still
provided.
0
1
Power-Down Mode.
In power-down mode, all the AD7794/AD7795 circuitry is powered down including the current sources, power
switch, burnout currents, bias voltage generator, and clock circuitry.
1
0
Internal Zero-Scale Calibration.
An internal short is automatically connected to the enabled channel. A calibration takes two conversion cycles to
complete when chop is enabled and one conversion cycle when chop is disabled. RDY goes high when the
calibration is initiated and returns low when the calibration is complete. The ADC is placed in idle mode following
a calibration. The measured offset coefficient is placed in the offset register of the selected channel.
1
0
1
Internal Full-Scale Calibration.
A full-scale input voltage is automatically connected to the selected analog input for this calibration.
When the gain equals 1, a calibration takes two conversion cycles to complete when chop is enabled and one
conversion cycle when chop is disabled.
For higher gains, four conversion cycles are required to perform the full-scale calibration when chop is enabled
and 2 conversion cycles when chop is disabled.
RDY goes high when the calibration is initiated and returns low when the calibration is complete. The ADC is
placed in idle mode following a calibration. The measured full-scale coefficient is placed in the full-scale register
of the selected channel.
Internal full-scale calibrations cannot be performed when the gain equals 128. With this gain setting, a system
full-scale calibration can be performed. A full-scale calibration is required each time the gain of a channel is
changed to minimize the full-scale error.
1
0
System Zero-Scale Calibration.
User should connect the system zero-scale input to the channel input pins as selected by the CH2 bit, CH1 bit,
and CH0 bit. A system offset calibration takes two conversion cycles to complete when chop is enabled and one
conversion cycle when chop is disabled. RDY goes high when the calibration is initiated and returns low when
the calibration is complete. The ADC is placed in idle mode following a calibration. The measured offset coeffi-
cient is placed in the offset register of the selected channel.
1
System Full-Scale Calibration.
User should connect the system full-scale input to the channel input pins as selected by the CH2 bit, CH1 bit, and
CH0 bit.
A calibration takes two conversion cycles to complete when chop is enabled and one conversion cycle when
chop is disabled. RDY goes high when the calibration is initiated and returns low when the calibration is
complete. The ADC is placed in idle mode following a calibration. The measured full-scale coefficient is placed in
the full-scale register of the selected channel.
A full-scale calibration is required each time the gain of a channel is changed.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-25B-MX-S | CONVERTER MOD DC/DC 95V 75W |
| VI-JNX-MX-S | CONVERTER MOD DC/DC 5.2V 75W |
| VI-2W3-MX-S | CONVERTER MOD DC/DC 24V 75W |
| AD7352YRUZ-RL | IC ADC DUAL 12BIT 3MSPS 16TSSOP |
| MS27467T11F98SA | CONN PLUG 6POS STRAIGHT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7794CRUZ-REEL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:6-Channel, Low Noise, Low Power, 24-/16-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
| AD7795BRUZ | 功能描述:IC ADC 16BIT 6CH LOW-PWR 24TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7795BRUZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:6-Channel, Low Noise, Low Power, 24-/16-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
| AD7795BRUZ-REEL | 功能描述:IC ADC 16BIT 6CH LOW-PWR 24TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7795BRUZ-REEL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:6-Channel, Low Noise, Low Power, 24-/16-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
发布紧急采购，3分钟左右您将得到回复。