- 您现在的位置：买卖IC网 > PDF目录10296 > AD7799BRU-REEL (Analog Devices Inc)IC ADC 24BIT 3CH LP 16-TSSOP PDF资料下载
参数资料
| 型号： | AD7799BRU-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 5/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT 3CH LP 16-TSSOP |
| 标准包装： | 2,500 |
| 位数： | 24 |
| 采样率（每秒）： | 470 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 2.5mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 3 个差分，单极；3 个差分，双极 |
| 配用： | EVAL-AD7799EBZ-ND - BOARD EVALUATION FOR AD7799 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
AD7798/AD7799
Rev. B | Page 13 of 28
ON-CHIP REGISTERS
The ADC is controlled and configured via a number of on-chip registers, which are described on the following pages. In the following
descriptions, set implies a Logic 1 state and cleared implies a Logic 0 state, unless otherwise stated.
COMMUNICATION REGISTER
RS2, RS1, RS0 = 0, 0, 0
The communication register is an 8-bit, write-only register. All communication to the part must start with a write operation to the
communication register. The data written to the communication register determines whether the next operation is a read or write
operation, and to which register this operation takes place. After the read or write operation is complete, the interface returns to its
default state, where it expects a write operation to the communication register. In situations where the interface sequence is lost, a write
operation of at least 32 serial clock cycles with DIN high returns the ADC to this default state by resetting the entire part. Table 9 outlines
the bit designations for the communication register. CR0 through CR7 indicate the bit location, with CR denoting that the bits are in the
communication register. CR7 denotes the first bit of the data stream. The number in parentheses indicates the power-on/reset default
status of that bit.
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
WEN(0)
R/W(0)
RS2(0)
RS1(0)
RS0(0)
CREAD(0)
0(0)
Table 9. Communication Register Bit Designations
Bit Location
Bit Name
Description
CR7
WEN
Write Enable Bit. A 0 must be written to this bit so that the write to the communication register occurs.
If a 1 is the first bit written, the part does not clock subsequent bits into the register. It stays at this bit
location until a 0 is written to this bit. Once a 0 is written to the WEN bit, the next seven bits are loaded
to the communication register.
CR6
R/W
Read/Write Bit. A 0 in this bit location indicates that the next operation is a write to a specified register.
A 1 in this position indicates that the next operation is a read from the designated register.
CR5 to CR3
RS2 to RS0
Register Address Bits. These bits are used to select the register during the serial interface communication.
CR2
CREAD
Continuous Read of the Data Register Bit. When this bit is set to 1 and the data register is selected, the
serial interface is configured so that the data register can be continuously read, that is, the contents of
the data register are placed on the DOUT pin automatically when the SCLK pulses are applied after the
RDY pin goes low to indicate that a conversion is complete. The communication register does not have
to be written to for data reads. To enable continuous read mode, the instruction 01011100 must be
written to the communication register. To exit the continuous read mode, the instruction 01011000
must be written to the communication register while the RDY pin is low. While in continuous read mode,
the ADC monitors activity on the DIN line for the instruction to exit continuous read mode. Additionally,
a reset occurs if 32 consecutive 1s are seen on DIN. Therefore, DIN should be held low in continuous read
mode until an instruction is to be written to the device.
CR1 to CR0
0
These bits must be programmed to Logic 0 for correct operation.
Table 10. Register Selection
RS2
RS1
RS0
Register
Register Size
0
Communication register during a write operation
8 bits
0
Status register during a read operation
8 bits
0
1
Mode register
16 bits
0
1
0
Configuration register
16 bits
0
1
Data register
16 bits (AD7798)/24 bits (AD7799)
1
0
ID register
8 bits
1
0
1
IO register
8 bits
1
0
Offset register
16 bits (AD7798)/24 bits (AD7799)
1
Full-scale register
16 bits (AD7798)/24 bits (AD7799)
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/26JC8SNLC | CONN HSG PLUG 8POS STRGHT SCKT |
| AD7450ABRM-REEL7 | IC ADC 12BIT W/DIFF INP 8-MSOP |
| MS3100F20-29P | CONN RCPT 17POS WALL MNT W/PINS |
| D38999/26FG75AN | CONN HSG PLUG 4POS STRGHT PINS |
| D38999/26FG75PNLC | CONN HSG PLUG 4POS STRGHT PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7799BRUZ | 功能描述:IC ADC 24BIT SIG-DEL 3CH 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7799BRUZ-REEL | 功能描述:IC ADC 24BIT 3CH LP 16-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD779AD | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit 128 kSPS Complete Sampling ADC |
| AD779AJ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog-to-Digital Converter， 14-Bit |
| AD779BD | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit 128 kSPS Complete Sampling ADC |
发布紧急采购，3分钟左右您将得到回复。