- 您现在的位置：买卖IC网 > PDF目录10304 > AD7829BRU-REEL7 (Analog Devices Inc)IC ADC 8BIT 8CH 2MSPS 28TSSOP PDF资料下载
参数资料
| 型号： | AD7829BRU-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 8BIT 8CH 2MSPS 28TSSOP |
| 标准包装： | 1,000 |
| 位数： | 8 |
| 采样率（每秒）： | 2M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 36mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 8 个单端，单极 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7822/AD7825/AD7829
Rev. C | Page 14 of 28
INPUT FREQUENCY (MHz)
50
38
0
1
2
.
01
S
NR
(
d
B)
3
4568
48
46
44
42
40
fSAMPLE = 2MHz
01
32
1-
0
18
Figure 18. SNR vs. Input Frequency on the AD7825
POWER-UP TIMES
The AD7822/AD7825/AD7829 have a 1 μs power-up time
when using an external reference and a 25 μs power-up time
when using the on-chip reference. When VDD is first connected,
the AD7822/AD7825/AD7829 are in a low current mode of
operation. Ensure that the CONVST line is not floating when
VDD is applied. If there is a glitch on CONVST while VDD is
rising, the part attempts to power up before VDD has fully settled
and can enter an unknown state. To carry out a conversion, the
AD7822/AD7825/AD7829 must first be powered up. The
AD7829 is powered up by a rising edge on the CONVST pin,
and a conversion is initiated on the falling edge of CONVST.
connected or after the AD7829 has been powered down using
the CONVST pin when using either the on-chip reference or an
external reference. When using an external reference, the falling
edge of CONVST may occur before the required power-up time
has elapsed; however, the conversion is not initiated on the
falling edge of CONVST but rather at the moment when the
part has completely powered up, that is, after 1 μs. If the falling
edge of CONVST occurs after the required power-up time has
elapsed, then it is upon this falling edge that a conversion is
initiated. When using the on-chip reference, it is necessary to
wait the required power-up time of approximately 25 μs before
initiating a conversion; that is, a falling edge on CONVST must
not occur before the required power-up time has elapsed, when
VDD is first connected or after the AD7829 has been powered
down using the CONVST pin, as shown in Figure 19.
VDD
tPOWER-UP
1s
CONVST
VDD
CONVST
tPOWER-UP
25s
CONVERSION
INITIATED HERE
CONVERSION
INITIATED HERE
EXTERNAL REFERENCE
ON-CHIP REFERENCE
0132
1-
019
Figure 19. AD7829 Power-Up Time
Figure 20 shows how to power up the AD7822 or AD7825 when
VDD is first connected or after the ADCs have been powered down,
using the PD pin or the CONVST pin, with either the on-chip
reference or an external reference. When the supplies are first
connected or after the part has been powered down by the PD
pin, only a rising edge on the PD pin causes the part to power
up. When the part has been powered down using the CONVST
pin, a rising edge on either the PD pin or the CONVST pin powers
the part up again.
As with the AD7829, when using an external reference with the
AD7822 or AD7825, the falling edge of CONVST may occur
before the required power-up time has elapsed. If this is the
case, the conversion is not initiated on the falling edge of CONVST,
but rather at the moment when the part has powered up
completely, that is, after 1 μs. If the falling edge of CONVST
occurs after the required power-up time has elapsed, it is upon
this falling edge that a conversion is initiated. When using the
on-chip reference, it is necessary to wait the required power-up
time of approximately 25 μs before initiating a conversion; that
is, a falling edge on CONVST must not occur before the
required power-up time has elapsed, when supplies are first
connected to the AD7822 or AD7825, or when the ADCs have
been powered down using the PD pin or the CONVST pin, as
shown in Figure 20.
相关PDF资料 |
PDF描述 |
|---|---|
| 14291-20PG-300 | CONN RCPT 20POS PNL MNT PIN |
| D38999/26FE6AN | CONN HSG PLUG 6POS STRGHT PINS |
| LTC2412IGN#PBF | IC ADC 2CH DIFF-IN 24BIT 16SSOP |
| A4FL | CONN PLUG CORD FMAL 4PIN FLEX |
| D38999/26WE6PNLC | CONN HSG PLUG 6POS STRGHT PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7829BRUZ | 功能描述:IC ADC 8BIT 8CH 2MSPS 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7829BRUZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:3 V/5 V, 2 MSPS, 8-Bit, 1-/4-/8-Channel Sampling ADCs |
| AD7829BRUZ-1 | 功能描述:IC ADC 8BIT 8CH 2MSPS 28-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7829BRUZ-1REEL7 | 功能描述:IC ADC 8BIT 8CH 2MSPS 28-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7829BRUZ-REEL | 功能描述:IC ADC 8BIT 8CHAN 2MSPS 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。