参数资料
| 型号： | AD783JRZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/8页 |
| 文件大小： | 0K |
| 描述： | IC AMP SAMPLE HOLD LP 5MA 8SOIC |
| 标准包装： | 1 |
| 放大器类型： | 采样和保持 |
| 电路数： | 1 |
| -3db带宽： | 15MHz |
| 电流 - 输入偏压： | 100nA |
| 电流 - 电源： | 9.5mA |
| 电流 - 输出 / 通道： | 5mA |
| 电压 - 电源，单路/双路(±)： | ±4.75 V ~ 5.25 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 管件 |
| 产品目录页面： | 773 (CN2011-ZH PDF) |
AD783
REV. A
–7–
The AD783 does not provide separate analog and digital ground
leads as is the case with most A-to-D converters. The common
pin is the single ground terminal for the device. It is the refer-
ence point for the sampled input voltage and the held output
voltage and also the digital ground return path. The common
pin should be connected to the reference (analog) ground of the
A-to-D converter with a separate ground lead. Since the analog
and digital grounds in the AD783 are connected internally, the
common pin should also be connected to the digital ground,
which is usually tied to analog common at the A-to-D converter.
Figure 3 illustrates the recommended decoupling and grounding
practice.
NOISE CHARACTERISTICS
Designers of data conversion circuits must also consider the
effect of noise sources on the accuracy of the data acquisition
system. A sample-and-hold amplifier that precedes the A-to-D
converter introduces some noise and represents another source
of uncertainty in the conversion process. The noise from the
AD783 is specified as the total output noise, which includes
both the sampled wideband noise of the SHA in addition to the
band limited output noise. The total output noise is the rms
sum of the sampled dc uncertainty and the hold mode noise. A
plot of the total output noise vs. the equivalent input bandwidth
of the converter being used is given in Figure 4.
300
0
1k
10M
200
100
10k
1M
100k
FREQUENCY – Hz
OUTPUT
NOISE
–
V
rms
Figure 4. RMS Noise vs. Input Bandwidth of ADC
DRIVING THE ANALOG INPUTS
For best performance, it is important to drive the AD783 analog
input from a low impedance signal source. This enhances the
sampling accuracy by minimizing the analog and digital cross-
talk. Signals which come from higher impedance sources (e.g.,
over 5 k
) will have a relatively higher level of crosstalk. For
applications where signals have high source impedance, an
operational amplifier buffer in front of the AD783 is required.
The AD711 (precision BiFET op amp) is recommended for
these applications.
HIGH FREQUENCY SAMPLING
Aperture jitter and distortion are the primary factors which limit
frequency domain performance of a sample-and-hold amplifier.
Aperture jitter modulates the phase of the hold command and
produces an effective noise on the sampled analog input. The
magnitude of the jitter induced noise is directly related to the
frequency of the input signal.
A graph showing the magnitude of the jitter induced error vs.
frequency of the input signal is given in Figure 5.
The accuracy in sampling high frequency signals is also
constrained by the distortion and noise created by the
sample-and-hold. The level of distortion increases with
frequency and reduces the “effective number of bits” of the
conversion.
Measurements of Figures 6 and 7 were made using a 14-bit
A/D converter with VIN = 5 V p-p and a sample frequency of
100 kSPS.
1%
1k
1M
0.1%
0.01%
10k
100k
FREQUENCY – Hz
APERTURE JITTER TYPICAL AT 20ps
1/2 BIT @
8 BITS
1/2 BIT @
10 BITS
1/2 BIT @
12 BITS
1/2 BIT @
14 BITS
Figure 5. Error Magnitude vs. Frequency
–65
–95
1M
–80
–90
1k
–85
100
–70
–75
100k
10k
FREQUENCY – Hz
THD
–
dB
Figure 6. Total Harmonic Distortion vs. Frequency
90
0
1M
20
10
10k
1k
30
40
50
60
70
80
100k
FREQUENCY – Hz
S/(N
+
D)
–
dB
Figure 7. Signal/(Noise and Distortion) vs. Frequency
相关PDF资料 |
PDF描述 |
|---|---|
| TSW-115-07-G-S | CONN HEADER 15POS .100" SGL GOLD |
| AD625KNZ | IC AMP INST 25MHZ LN 16DIP |
| TSW-109-05-G-S | CONN HEADER 9POS .100" SGL GOLD |
| AD526ADZ | IC AMP PGA 10MA 16CDIP |
| 53324-0560 | CONN HEADER 2MM 5POS PCB TIN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD783SQ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Sample/Track-and-Hold Amplifier |
| AD783SQ/883B | 制造商:Rochester Electronics LLC 功能描述:IC, 12-BIT 250 NS S/H AMP - Bulk |
| AD7840 | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS Complete 14-Bit DAC |
| AD7840AQ | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
| AD7840ARS | 功能描述:IC DAC 14BIT LOW POWER 5V 24SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
发布紧急采购，3分钟左右您将得到回复。