- 您现在的位置：买卖IC网 > PDF目录9713 > AD7873ARUZ-REEL (Analog Devices Inc)IC ADC 12BIT TOUCHSCREEN 16TSSOP PDF资料下载
参数资料
| 型号： | AD7873ARUZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/29页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT TOUCHSCREEN 16TSSOP |
| 标准包装： | 2,500 |
| 类型： | 电阻 |
| 触摸面板接口： | 4 线 |
| 输入数/键： | 1 TSC |
| 分辨率（位）： | 12 b |
| 评估套件： | 可供 |
| 数据接口： | 串行 |
| 数据速率/采样率 (SPS，BPS)： | 125k |
| 电压基准： | 外部，内部 |
| 电源电压： | 2.2 V ~ 5.25 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
AD7873
Data Sheet
Rev. F | Page 16 of 28
the AD7873 is approximately 70 . In this mode of operation,
therefore, some voltage is likely to be lost across the internal
switches, and it is unlikely that the internal switch resistance
will track the resistance of the touch screen over temperature
and supply, providing an additional source of error.
Figure 28. Single-Ended Reference Mode (SER/DFR = 1)
The alternative to this situation is to set the SER/DFR bit low.
Again, making a Y coordinate measurement is considered, but
now the +REF and –REF nodes of the ADC are connected
directly to the Y+ and Y– pins. This means the analog-to-digital
conversion is ratiometric. The result of the conversion is always
a percentage of the external resistance, independent of how it
could change with respect to the on resistance of the internal
switches. Figure 29 shows the configuration for a ratiometric
Y coordinate measurement.
Figure 29. Differential Reference Mode (SER/DFR = 0)
The disadvantage of this mode of operation is that during both
the acquisition phase and conversion process, the external
touch screen must remain powered. This results in additional
supply current for the duration of the conversion.
MEASUREMENTS
Temperature Measurement
Two temperature measurement options are available on the
AD7873, the single conversion method and the differential
conversion method. Both methods are based on an on-chip
diode measurement.
In the single conversion method, a diode voltage is digitized
and recorded at a fixed calibration temperature. Any subsequent
polling of the diode provides an estimate of the ambient tempera-
ture through extrapolation from the calibration temperature
diode result. This assumes a diode temperature drift of
approximately –2.1 mV/°C. This method provides a resolution
of approximately 0.3°C and a predicted accuracy of ±3°C.
The differential conversion method is a two-point measurement.
The first measurement is performed with a fixed bias current
into a diode, and the second measurement is performed with a
fixed multiple of the bias current into the same diode. The
voltage difference in the diode readings is proportional to
absolute temperature and is given by the following formula:
(
)
( )
N
q
kT
VBE
ln
/ ×
=
where:
VBE represents the diode voltage.
N is the bias current multiple.
k is Boltzmann’s constant.
q is the electron charge.
This method provides more accurate absolute temperature
measurement of ±2°C. However, the resolution is reduced to
approximately 1.6°C. Assuming a current multiple of 105
(typical for the AD7873) taking Boltzmann’s constant,
k = 1.38054 ×10–23 electrons volts/degrees Kelvin, the electron
charge q = 1.602189 × 10–19, then T, the ambient temperature in
degrees centigrade, can be calculated as follows:
(
) (
)
(
) (
)
Κ
273
10
49
.
2
)
C
(
ln
/
ln
/
3
/
×
=
°
×
=
×
=
BE
V
T
N
k
q
V
T
N
q
kT
V
where VBE is calculated from the difference in readings from
the first conversion and second conversion.
Figure 30 shows a block diagram of the temperature
measurement mode.
Figure 30. Block Diagram of Temperature Measurement Circuit
+VCC
VREF
GND
Y+
Y–
X+
IN+
IN–
REF+
ADC CORE
REF–
02164-
028
+VCC
GND
Y+
Y–
X+
IN+
IN–
REF+
ADC CORE
REF–
02164-
029
I
TEMP0
TEMP1
105 × I
MUX
ADC
02164-
030
相关PDF资料 |
PDF描述 |
|---|---|
| AD7873ACPZ-REEL | IC ADC 12BIT TOUCHSCREEN 16LFCSP |
| AD7879-1WARUZ-RL7 | IC ADC 12BIT CTRLR TOUCH 16TSSOP |
| VI-BTL-IV-B1 | CONVERTER MOD DC/DC 28V 150W |
| AD7879-1WACPZ-RL7 | IC ADC 12BIT CTRLR TOUCH 16LFCSP |
| AD7879WARUZ-RL7 | IC ADC 12BIT CTLR TOUCH 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7873ARUZ-REEL7 | 功能描述:IC ADC 12BIT TOUCHSCREEN 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:- 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD7873BCP | 制造商:Analog Devices 功能描述:TOUCH SCREEN DIGITIZER 制造商:Rochester Electronics LLC 功能描述:2.7V 12-BIT TOUCH SCREEN DIGITIZER I.C. - Bulk |
| AD7873BCP-REEL | 制造商:Analog Devices 功能描述:TOUCH SCREEN DIGITIZER |
| AD7873BCP-REEL7 | 制造商:Analog Devices 功能描述:TOUCH SCREEN DIGITIZER 制造商:Analog Devices 功能描述:2.7V 12-BIT TOUCH SCREEN DIGITIZER I.C. - Tape and Reel |
| AD7873BCPZ | 制造商:Analog Devices 功能描述:TOUCH SCREEN DIGITIZER |
发布紧急采购，3分钟左右您将得到回复。